PENTAGON DefendaGuard Скачать руководство пользователя страница 25

Страница: 25 / 28

FOUR: COMPLETE

COMPLETE

1. Put the curtain down into the closed

position.

3. Replace the box housing (A) cover lid

and secure it with the four screws you

removed in stage 1 of the installation.

If your shutter has support brackets:

Remove the support brackets (K) in

order to complete the next step.

If your shutter has support brackets:

Replace the support brackets (K) you

removed in step 2.

If your shutter is installed outdoors:

The shutter must be sealed to the wall.

Put a good bead of suitable exterior

caulking where the shutter meets the

wall along the top and on both sides of

the shutter.

To operate the shutter, pull the tape in

the upwards direction so that the tape

goes into the box housing (A). To open

the shutter, pull the tape out of the box

housing and down to the tape coiler.

Содержание DefendaGuard





























Результаты поиска

Содержание DefendaGuard

Отзывы:

Похожие инструкции для DefendaGuard

Бренды по названию

Популярные бренды

PENTAGON DefendaGuard, Ручное управление

Результаты поиска

Содержание DefendaGuard

Отзывы:

Похожие инструкции для DefendaGuard

Бренды по названию

Популярные бренды