Pelton & Crane Helios HL3CB Скачать руководство пользователя страница 5

Страница: 5 / 44

053154 r17

WaRnInG:

Only authorized service

technicians should attempt to service

this equipment. Use of other than

authorized technicians will void the

warranty.

WaRnInG:

Use a licensed electrician

for all wiring.

WaRnInG:

Failure to disinfect

the dental operating light between

patients could expose user/patient to

cross contamination and bio-burden/

bio-contamination.

WaRnInG:

To avoid risk of electric

shock, this equipment must be

connected

only

to supply mains with

protective earth.

WaRnInG:

No modification of this

equipment is allowed.

Electrical Specifications

All fuses are labeled at point of use.

Replace fuses only with type and rating

as indicated.

Volts Cycles Amps

115 VAC 60 HZ 1 A ~

230 VAC 50 HZ .6 A ~

IEC Medical Device Classification

Classification:

Type:

Operation Mode:

Continuous

Splash Protection: IPX0

WaRnInG:

The Helios light is not to

be used in rooms where an explosion

hazard exists.

WaRnInG:

Rotational stops are designed for a

maximum force limit of 25 lbs. If rotational stops

are broken, immediately take the equipment

out of use and have the equipment serviced.

Operation of damaged equipment could result in

injury to the operator and/or patient.

storage Conditions:

-4°F to 122°F/ -20°C to 50°C

10% to 90% Relative Humidity

As manufacturers of electro-medical products we can assume responsibility for safety-related performance of the

equipment only if maintenance, repair and modifications are carried out only by us or agencies we have authorized for

this purpose, and if components affecting safe operation of the unit that may be needed are replaced with original parts.

We suggest that you request a certificate showing the nature and extent of the work performed, from those who carry out

such work, and specify that the certificate show any changes in rated parameters or working ranges, as well as the date,

the name of the firm and a signature.

safeTy noTes

WaRnInG:

Failure to install set

screws & roll pin per Installation

Instructions could result in injury or

damage to equipment.

WaRnInG:

Power cords and their associated

parts cannot be substituted without increased

risk of electric shock or fire. We recommend the

use of Pelton & Crane replacement parts only!

Power cords must be installed by qualified

personnel. Make sure all service loops, strain

reliefs, and cord guards are in place and that

line, neutral and ground wires are secured.

WaRnInG:

This product must be disinfected

before use.

Содержание Helios HL3CB













































Результаты поиска

Содержание Helios HL3CB

Отзывы:

Бренды по названию

Популярные бренды

Pelton & Crane Helios HL3CB, Руководство по установке

Результаты поиска

Содержание Helios HL3CB

Отзывы:

Бренды по названию

Популярные бренды