background image

INTRODUCTION

ENVIRONMENTAL PROTECTION

Your equipment comprises numerous materials which can be valorised or recycled. Entrust 

these to your reseller or to an approved service centre so that they can be processed.

Comply with the regulations in force in your country as concerns environmental protection 

associated with your activity.

All through this user guide you will find advisory notes and information entitled: 

REMARK

CAUTION 

WARNING

.

REMARK

 provides additional information, clarifies a point or explains a step to be followed in detail.

The 

CAUTION

 and 

WARNING

 advisories are used to define a procedure which, if neglected or incorrectly 

performed, may lead to serious damage to the equipment and/or personal injury.

This advisory: 

G

 indicates that if the procedures or instructions are not complied with, any damage will not 

be covered by the warranty and the owner will be responsible for the repair costs.

Safety indications are also given on the tool; they remind you of the safety precautions to be taken. Identify 

and read these indications before using the tool. Immediately replace any indications that may become 

partially illegible or deteriorated.

Refer to the «SAFETY INDICATIONS» heading in order to identify the location of the safety 

indications on the tool.

No part of this manual may be reproduced without the written consent of PELLENC S.A.. The technical 

characteristics and the illustrations given in this manual are for information purposes and are in no way 

contractual. PELLENC S.A. reserves the right to make any modification or improvement to its products 

as deemed necessary without informing customers already in possession of a similar model. This manual 

forms an integral part of the tool and must accompany the tool if it changes hands.

SAFETY INSTRUCTIONS

You must read THE WHOLE of this user guide before using the tool or before carrying out 

servicing operations.

Comply scrupulously with the instructions and illustrations given in this document.

KEEP THESE INSTRUCTIONS

This manual contains important information and operating instructions for the following tool 

: HELION Pole & Telescopic

Содержание HELION POLE TELESCOPIC























Отзывы: