Peg-Perego Pliko P3 Pramette, Инструкция по эксплуатации

Страница: 18 / 68

EN_English
Thank you for choosing a Peg-
Pérego product.
• Peg-Pérego S.p.A. is ISO 9001 certified.
• This certification offers customers and
consumers a guarantee of transparency
and confidence in the company’s mode of
operation.
WARNING
• IMPORTANT: read these instructions carefully and
keep them for future use. The child’s safety could be
at risk if these instructions are not followed.
• This item was designed for the transport of 1 child in the
seat and 1 one child standing on the rear footboard.
• Do not use this item for a number of occupants greater
than that intended by the manufacturer.
• This item is approved for children from birth up to a
weight of 15 kg in the seat. The rear footboard is approved
for the transport of a second child up to a weight of 20 kg.
• This item was designed for use in combination with the
following Peg Perego Ganciomatic products: the “Primo
Viaggio” car seat (Group 0+) - the “Navetta” bassinet unit.
• Before use check that the Peg Perego Ganciomatic
products are correctly fixed to the item.
• The assembly and preparation of the item must be carried
out by an adult.
• Do not use this item if there are parts missing or signs of
breakage.
• Always use the five point harness; always use the harness
crotch strap in combination with the waist strap.
• It may be dangerous to leave your child unattended.
• Always apply the brake when stationary.
• Before use check that all the attachment mechanisms are
correctly engaged.
• Do not insert fingers into the mechanisms.
• Be careful not to hurt the child when adjusting the
mechanisms (handlebar, backrest).
• Any weights hanging on the handlebar or handles
could make the item unstable; follow the manufacturer’s
instructions as regards the maximum loads transportable.
• The front bar is not designed to support the child’s
weight. It is not designed to keep the child in the seat and
does not substitute for the waist belt.
• Do not load the baskets over 5 kg. Do not put weight in
the cup holder in excess of those indicated on the cup
holders themselves and never hot drinks. Do not put loads
of more than 0.2 kg in the hood pockets (if present).
• Do not use the item near to stairs or steps, heat sources,
naked flames or dangerous objects within reach of the
child.
• The use of accessories not approved by the manufacturer
could be dangerous.
• This item is not suitable for jogging or roller skating.
• Apply the brake when loading or unloading children.
instructions for use
OPENING
1• Before opening the stroller remove the two protective
caps from the hooks as shown in the figure. Otherwise,
the stroller will not open correctly.
2• To open the stroller, pull up the two levers on the handles
and
3• at the same time, lift the stroller, which will open
automatically. To make sure that the stroller has been set
up correctly, check the two side hooks (see figure).
ASSEMBLYING THE STROLLER
4• To mount the front wheels, lower Lever A and slip the
wheels onto the axle, as shown in the figure. Press until
the wheels click into place.
5• To assemble the rear wheels fasten the wheels connected
by the break wire, as indicated in the figure.
6• Carefully distinguish the left wheel from the right, to
fasten the two rear wheels properly. The left wheel
has a rib on the wheel tube and one on the chassis to
guarantee proper fastening (see figure).
7• Make sure that it is fastened properly, as indicated in the
figure (click).
8• The stroller comes with caps on the armrests. To attach
the front bar, remove the caps first. (Keep the caps, in
case you want to use the stroller without the front bar).
To remove the caps, press the buttons under the armrests
while pulling the caps off.
9• To attach the front bar, insert the two ends of the bar into
the armrests and press until the bar clicks into place, as
shown in the figure.
10• To mount the basket, slide the slots onto the front hooks
A and the rear hooks B and C.
11• The figure shows the mounted basket.
12• The drink holder can be placed on the left or right hand
side of the stroller, thanks to the attachment which is
already fitted on both sides. To fit the drink holder, click it
on, as in Figure A. See Figure B for a fitted drink holder.
PLIKO P3 VERSIONS
13• “Classico” Model: comes with a hood.
14• “Completo” Model: comes with hood, cover, and rain
canopy.
HOOD
• The hood comes with a zipper, for attaching the zip-on
rain canopy or mosquito netting (see Accessories Line).
15• To mount the hood, push the fittings down until they
click, as shown in the figure.
16• As shown in the figure, button the hood inside the
armrest and the backrest of the stroller.
17• To stretch out the hood, push the coupling downward.
The hood can be reclined by following the inclination of
the backrest.
18• The hood is supplied with the front border folded up. It
should not be used like this however. In order to be able
to use the hood correctly, turn the edge up, as in the
figure.
19• It is possible to detach the back part of the fabric by
unzipping it and use the hood as a sun canopy.
20• To reattach the back part of the fabric, proceed as
indicated in the figure.
21• By lowering the stroller backrest, the hood extends and,
thanks to the double zipper, a window can be created
to allow more air to circulate and see the child when
sleeping.
22• To remove the hood, you must unbutton it from the
stroller, loosen the couplings and raise the tabs of the
fasteners, pushing towards the inside of the stroller.
23• The hood, thanks to its reversible attachment system, can
also be installed on the part opposite the handles. Before
removing the hood to turn it around, close it and bring it
right forward to rotate the fasteners, then detach it and
reinstall it on the opposite part; you can even rotate the
fasteners with your hands.
COVER
24• To fasten the cover, zip it with the zipper of the footboard,
as shown in the figure.
Fasten the magnet as in Figure B to attach the hood.
RAIN CANOPY
25• To mount the rain canopy, zip it to the hood.
26• It is necessary to release the button on the hood, as in the
figure, but leave the tab underneath attached.
27• Fasten the button found on the elastic to the stroller
button until you hear a click, as indicated in the figure.
28• Fasten the lowermost elastic of the rain canopy to the
wheel.