PEERLESS FPE42F-B страница 15 Скачать руководство пользователя

Страница: 15 / 18

15 of 18

ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11

Refer to screen manufacturers' requirements for optimal environment temperature. If screen manufacturer's
requirments state that cooler or warmer temperatures are acceptable, use a fl atblade screwdriver to adjust dial to
desired temperature.

NOTE:

Thermostat inside enclosure assembly will determine at what time the Exhaust Fan will initiate. The Intake

Fan will operate at all times. For all other questions, refer to thermostat instruction sheet included in enclosure
assembly

HEATER INFORMATION (FPE42FH-S only)

Thermostat of heater is not adjustable. The heater will turn
on at 40°±7° and will turn off at 60°±5°.

Heater uses a 20 amp fuse.

Setting Thermostat

DIAL

• Frame of heater will be hot when turned on. Turn

heater off allowing frame to cool prior to service.

WARNING

• Do not postion AV and power cables close to heater

or damge to cables may occur.

CAUTION

HEATER

THERMOSTAT

Содержание FPE42F-B



















Результаты поиска

Содержание FPE42F-B

Отзывы:

Похожие инструкции для FPE42F-B

Бренды по названию

Популярные бренды

PEERLESS FPE42F-B, Инструкция по установке и сборке

Результаты поиска

Содержание FPE42F-B

Отзывы:

Похожие инструкции для FPE42F-B

Бренды по названию

Популярные бренды