© COPYRIGHT 2010 PECO, INC. ALL RIGHTS RESERVED.
P/N 70476 3220-2265 REV 01
7
taBle 2. aDvanceD conFIGUratIon (cont.)
menU
FeatUre
oPtIons
stD.moDel
DeFaUlt
DescrIPtIon / comments
340
Keypad Lockout
0-3
0
Restricts access to certain features of device; Service Menu still available if enabled.
0 = No key pad lockout (Default)
1 = Disables Schedule and System keys
2 = Disables Schedule, System, and Fan keys
3 = Disables all keys
341
Enable Pin Access
0,1
0
Applies a 3 digit access code to enter Service Menu 342
0 = Disable,
1 = Enable
342
Set PIN Access
Code
000-999
000
Choose a 3-digit code.
350
Fan Mode
Enable
1-3
3
1 = ON: Fan is turned on regardless of demand.
2 = Auto: Fan is turned on according to heating or cooling demand.
3 = ON or Auto: Allows occupant to select either 1 or 2 above.
360
System Mode
Enable
0-3
1
Allows ability to determine which system modes the occupant can select.
0 = OFF, Auto
1 = OFF, Heat, Cool, Auto
2 = OFF, Heat, Cool
3 = Heat, Cool, Auto
380
Minimum Deadband
Adjustment
3-10°F, 1.5-5°C
3°F
Select a changeover deadband value to prevent short cycling between heating and cooling modes.
The value is adjustable to meet various HVAC system requirements.
390
Pre-Occupancy
Purge
0-3 hours
0 hours
Select to energize fan for selected number of hours (0-3) prior to all occupied events.
395
Maximum Override
Time Limit
0=Time until next
event; or
1-4 hours
3
Restricts the duration that a temporary hold can be set. The temporary hold is limited by the maximum
amount of time as defined in this Service Menu.
0 = Remainder of time until the next scheduled event.
1 = 1 Hour
2 = 2 Hours
3 = 3 Hours
4 = 4 Hours
400
Cycles Per Hour
(CPH)
Cooling Stage 1
0-6 CPH
3 CPH
Defines the number of cycles per hour for cooling (Stage 1). Select 0 to enable ON-OFF control for
Stage 1 cooling.
410
Cycles Per Hour
(CPH)
Cooling Stage 2
0-6 CPH
3 CPH
Defines the number of cycles per hour for cooling (Stage 2). Select 0 to enable ON-OFF control for
Stage 2 cooling.
420
Cycles Per Hour
(CPH)
Heating Stage 1
0-12 CPH
5 CPH
Defines the number of cycles per hour for heating (Stage 1). Select 0 to enable ON-OFF control for
Stage 1 heating.
430
Cycles Per Hour
(CPH)
Heating Stage 2
0-12 CPH
5 CPH
Defines the number of cycles per hour for heating (Stage 2). Select 0 to enable ON-OFF control for
Stage 2 heating.
450
Cycles Per Hour
(CPH)
Heating Stage 3
0-12 CPH
5 CPH
Defines the number of cycles per hour for heating. Select 0 to enable ON-OFF control for
Heating Stage 3.
460
Heat Recovery Rate
0-18°F/Hr
0-10°C/Hr
5°F/Hr
Defines the rate at which the device achieves the heat comfort setpoint. Select 0 to disable ramp
recovery.
470
Cool Recovery Rate
0-18°F/Hr
0-10°C/Hr
5°F/Hr
Defines the rate at which the device achieves the cool comfort setpoint. Select 0 to disable ramp
recovery.
480
Minimum Off Time
1-10 minutes
4 minutes
Sets the minimum off time for both the heat and cool output.
490
Humidity Control
Enable
(Select models only)
Selects how humidity will be controlled. When dehumidify control is enabled, the Y2 terminal becomes
dehumidify.
0 = Disabled
1 = Dehumidify Control
500
Programmable/
Intermittent Fan
0-2
0
0 = Disable
1 = Programmable Fan: Fan operates continuously in occupied periods or with demand in
unoccupied periods.
2 = Intermittent Fan: Fan operates based on the on and off times set in menus 501 and 502.
