manualshive.com logo in svg

Peavey 03620490, Руководство пользователя

Поделиться
Скачать
Peavey 03620490 Скачать руководство пользователя страница 40

Loudspeaker System Specifications 

38 

may be necessary to turn them full ON or full OFF to eliminate or reduce hum. 
This is a typical AC wiring/light dimmer interference problem, not a design flaw of 
the 

PVX™p 15 Bluetooth®. 

 
The third wire (ground plug) on the AC plug should NEVER be removed or 
broken off, as this is a potential safety hazard. 
 

Distorted or Fuzzy Sound 

First, ensure the mixer (signal source) is not clipping or being overdriven. Make 
sure the Level (6) control on the PV

X™p 15 Bluetooth® has not been set too low.   

Make sure that the MIC/LINE Switch (6), is not in the mic position when driving 
the system with a line level signal.  The analog input circuitry and the DSP 
system will overload and cause severe distortion that 

can not

 be removed by 

turning down the Level control ! 
 
Check that the input plug is fully seated in the input jack on the rear panel of the 
PVX™p 15 Bluetooth®.   
Ensure that a power amp has not been plugged into the input jack of the 

PVX™p 

15 Bluetooth®.   
If an extension cord is being used to provide the AC power to the unit, insure that 
it is of sufficient current capacity and that it is not also being used to supply 
power to any other device.  
 
The 

PVX™p 15 Bluetooth® has built-in EQ to extend and smooth the natural 

response of the speakers in the system.  If excessive additional bass boost or HF 
boost have been added externally to the 

PVX™p 15 Bluetooth®, it could cause 

premature overload at high SPL.  Reduce the amount of any external (mixer, 
rack) EQ and see if that clears up the distortion. 
 
Finally, realize that even though the 

PVX™p 15 Bluetooth® is a powerful and 

high output unit, it does ultimately have limits, and it may need additional 
powered units (or a subwoofer) to provide enough sound output or coverage. In 
this case, try turning the mixer levels down a little to see if that clears things up.  
If, after checking all the things listed to check and anything else you can think of 
to check safely, and the system still exhibits problems, carefully note all 
conditions and check with your Peavey dealer for advice. 
 

Care and Maintenance 

Your 

PVX™p 15 Bluetooth® is a sturdy and durable product and will provide 

years of reliable use if properly cared for. Use common sense and read the 
safety warnings to avoid hazardous operating conditions. 
 
The unit must be disconnected from the AC power source before any work is 
done on it. Refer all servicing to qualified service personnel. 
 

Содержание 03620490














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды