manualshive.com logo in svg

PCS PCPGW, Руководство пользователя

Поделиться
Скачать
PCS PCPGW Скачать руководство пользователя страница 50

47 | 

P a g e

The button press sequences listed below are given as x-y-z. Where x, y, and z are the number of times 

to press and release the button.  The dash character represents a short pause.  The button presses 

need to come in a regular sequence that is not too fast and not too slow.  A normally paced rhythm 

works well:  Press and hold down for ½ second or so then release, wait ½ a second or so and press and 

release again.

To carry out these button press sequences it is best to have the Gateway plugged into a power strip so 

that it is horizontal and you can see the yellow (left) and green (right) small rectangular LEDs on either 
side of the network connection.

How to set the Gateway to DHCP mode without a full factory reset

Why use this procedure? The Gateway is set to a static IP address and you now want to use it on a 

network where it needs to get its IP address from a DHCP server.

Step 1. Have the Gateway powered on for at least 60 seconds before beginning.  

The Gateway must 

have the network cable plugged in and connected to the network or this procedure will not work

. 

Press and hold the Gateway button though the hole on the side of the Gateway with a bent paperclip 

(see the "Where is the Gateway button" section above) for about 30 seconds until the green (right) LED

on the network connector is blinking 2 times per second continuously. You may see the LEDs blink in 

other ways during this time but keep pressing the button until you see the 2-times per second blinking. 
The Gateway is now in “boot loader mode”.

Step 2.  Press the Gateway button the 

sequence 5-3-2.

  This configures the Gateway to use DHCP 

mode. This will not take effect until a power cycle. If the Gateway contains firmware version 1.4 or 

later then the Gateway will restart at this point and step 3 below is not needed.

If the Gateway contains earlier firmware then the Gateway green (right) LED will repeatedly 1 slow 

blinks to show this was done and you should proceed to step 3.

Step 3. Power cycle the Gateway.

Once this is complete you can connect using UPStart, discover the address of the Gateway and 

connect.

Содержание PCPGW





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды