Patton SmartNode 4830 Series Скачать руководство пользователя | Manualshive

Страница: 2 / 89

background image

Patton Electronics Company, Inc.

7622 Rickenbacker Drive

Gaithersburg, MD 20879 USA

Tel: +1 (301) 975-1000

Fax: +1 (301) 869-9293

Support: +1 (301) 975-1007

URL:

www.patton.com

E-Mail:

[email protected]

Trademark Statement

The terms

SmartWare and SmartView

are trademarks of Patton Electronics Company.

All other trademarks presented in this document are the property of their
respective owners.

Copyright © 2012, Patton Electronics Company. All rights reserved.

The information in this document is subject to change without notice. Patton Elec-
tronics assumes no liability for errors that may appear in this document.

Warranty Information

The software described in this document is furnished under a license and may be used
or copied only in accordance with the terms of such license.

Patton Electronics

warrants all SmartNode product components to be free from

defects, and will—at our option—repair or replace the product should it fail within
one year from the first date of the shipment.

This warranty is limited to defects in workmanship or materials, and does not cover
customer damage, abuse or unauthorized modification. If the product fails to perform
as warranted, your sole recourse shall be repair or replacement as described above.
Under no condition shall

Patton Electronics

be liable for any damages incurred by

the use of this product. These damages include, but are not limited to, the following:
lost profits, lost savings and incidental or consequential damages arising from the use
of or inability to use this product.

Patton Electronics

specifically disclaims all other

warranties, expressed or implied, and the installation or use of this product shall be
deemed an acceptance of these terms by the user.

«
1
2
3
4
...
»

Содержание SmartNode 4830 Series


























































































Отзывы:

Нет отзывов

Похожие инструкции для SmartNode 4830 Series

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды