Patton Kamado 21, Оригинальные инструкции по эксплуатации и сборке, Страница: 36 / 71

GB, IE
36
Parts list
Prior to Assembly: Read the instructions carefully. Check all parts against the parts list.
Carry out assembly on a soft surface to avoid scratching the paint. Please retain this information for future reference.
For ease of assembly on ly loosely ti ghten bolts and then tighten fully when assembly is complete.
WARNING - DO NOT over tighten bolts; only tighten with moderate pressure to avoid damaging the bolts or
components of the Kamado Gril.
Assembly Instructions
IMPORTANT - Remove any packaging before use, but retain the safety instructions and store them with this product.
ASSEMBLY
STEP 1 - Attach the four pre-threaded castor wheels (2 & 3) to each of the four brackets (1) by pushing them
through the hole. Using an adjustable spanner secure each castor wheel with 1x nut (B).
STEP 2 - To assemble the cart insert the two cross pieces (4) into one of the four brackets (1) from both the top and
bottom.
STEP 3 - Continue to insert the cross pieces (4) into the other three brackets (1).
STEP 4 - Secure the brackets (1) to the cross pieces (4) by using the 16x screws (A). Make sure the cart is secure
and all of the screws are tight before placing the Kamado Grill (9) into it.
STEP 5 - To place the Kamado Grill (9) on the cart first remove all of the items that are inside of the grill to make
lifting easier.
STEP 6 - Use a minimum of two people when lifting the Kamado Grill onto the cart. Place one of your hands in the
bottom vent of the Kamado and the other under the grill. Lifting by the hinge or the side tables could result
in injury and will void the warranty if damage occurs.
STEP 7 - Place the Kamado Grill on the cart with the bottom vent facing to the front of the cart allowing the vent
to open and close without any interrution.
STORAGE
• When not in use, and if stored outside, cover the Kamado once completely cooled with a suitable rain cover.
• The chrome plated cooking grill is NOT dishwasher safe; use a mild detergent with warm water.
• When using the Kamado push down on both of the locking wheels to stop the unit moving about during use.
• It is recommended the Kamado be stored under cover in a garage or shed over winter for complete protection.
CLEANING
• The Kamado is self cleaning. Heat it up to 260ºC for 30 minutes and it will scorch off all of the food and debris.
• DO NOT use water or any other types of cleaning product to clean the inside of your Kamado. The walls are
porous and will absorb any fluids used, this could cause the Kamado to crack. If the soot becomes excessive
then use a wire brush or the ash tool (not supplied) to scrape off the carbon remnants before the next use.
• To clean the grills and grates use a non-abrasive cleaner once the unit has fully cooled.
• To clean the outer surface wait until the Kamado is cool and use a damp cloth with a mild detergent.
MAINTENANCE
• Tighten the bands and oil the hinge 2 times a year or more if needed.
LIGHTING, USAGE AND CARE INFORMATION
• Ensure the Kamado is positioned on a permanent, flat, level, heat resistant non-flammable surface away
from flammable items.
• Ensure the Kamado has a minimum of 2m overhead clearance and has a minimum 2m clearance from
other surrounding items.
• To start a fire place rolled up
in the base of the Kamado. Then place 2 or 3 handfuls of lump charcoal over the top of the newspaper.
• DO NOT use petrol, white spirit, lighter fluid, alcohol or other similar chemicals for lighting or relighting.
• Open the bottom vent and light the newpaper using a long nosed lighter or safety matches. Once it has
caught, leave the bottom vent and lid open for about 10 minutes to build a small bed of hot embers.
• Allow the charcoal to heat up and be kept red hot for at least 30 minutes prior to the first cooking on the
kamado. DO NOT cook before the fuel has a coating of ash.
• It is recommended you don’t stoke or turn the coals once they are alight. This allows the charcoals to burn
more uniformly and efficiently.
• Once alight ONLY use heat resistant gloves when handling hot ceramics or cooking surfaces.
• See below for cooking instuctions depending on temperature and duration.
LOW TEMPERATURE COOKING GUIDE
• Light the lump charcoal according to the the instructions above. DO NOT move or stoke the coals once lit.
• Open the bottom vent fully and leave the lid open for about 10 minutes to build a small bed of hot embers.
• Monitor the Kamado until it has risen to the desired temperature. See page 4 for a temperature cooking guide.
• Fully close the bottom vent to maintain the temperature.
• You are now ready to use the Kamado for cooking on.
• IMPORTANT: When opening the lid at high temperatures it is essential to lift the lid only slightly, allowing air
to enter slowly and safely, preventing any backdraft or flare-ups that may cause injury.
• ALWAYS follow the FOOD COOKING INFORMATION stated on page 4 of this instruction manual.
• ALWAYS use heat resistant gloves when handling hot ceramics or cooking surfaces.
SMOKING GUIDE
• Follow the instructions above as if you were starting a slow cook.
• Monitor the Kamado until it has risen to the desired temperature. See page 4 for a temperature cooking guide.
• Leave the bottom vent slightly open.
• Close the top vent and continue to check the temperature for a few more minutes.
• Using heat resistant gloves sprinkle the wood chips in a circle over the hot charcoal.
• You are now ready to use the Kamado to smoke on.
• TIP: Soak your wood chips or cooking planks in water for 15 minutes to prolong the smoking process.
• IMPORTANT: When opening the lid at high temperatures it is essential to lift the lid only slightly, allowing air
to enter slowly and safely, preventing any backdraft or flare-ups that may cause injury.
• ALWAYS follow the FOOD COOKING INFORMATION stated on page 4 of this instruction manual.
• ALWAYS use heat resistant gloves when handling hot ceramics or cooking surfaces.
5
IMPORTANT - Remove any packaging before use, but retain the safety instructions and store them with this product.
Ensure that the lid is closed prior to assembly.
Assembly instructions
Parts list
WARNING - DO NOT over tighten bolts; only tighten with moderate pressure to avoid damaging the bolts or
components of the Kamado Grill.
Prior to assembly, read the instructions carefully. Check all parts against the parts list.
Carry out assembly on a soft surface to avoid scratching the paint. Please retain this information for future reference.
For ease of assembly only loosely tighten bolts and then tighten fully when assembly is complete.
1
B
2
STEP 1 - Attach the four pre-threaded castor wheels (2 & 3) to each of the four brackets (1) by pushing them
through the hole. Using an adjustable spanner secure each castor wheel with 1x nut (B).
2 (2x)
3 (2x)
6 (1x)
5 (1x)
10 (
2
x)
11 (1x)
12 (
1
x)
13 ( � x)
14 ( x)
15 (2x)
7 (1x)
8 (1x)
9 (1x)
1 (4x)
4 (2x)
C (2x)
D (2x)
A (16x)
B (4x)
E (2x)
F (4x)
G (2x)
H (2x)
16 (2x)
1
1