background image

11

SmartNode 4940 Getting Started Guide 

Safety when working with electricity

Do not open the device when the power cord is connected. For systems 
without a power switch and without an external power adapter, line volt-
ages are present within the device when the power cord is connected.

For devices with an external power adapter, the power adapter shall be a 
listed 

Limited Power Source

 The mains outlet that is utilized to power the 

device shall be within 10 feet (3 meters) of the device, shall be easily 
accessible, and protected by a circuit breaker in compliance with local regu-
latory requirements.

For AC powered devices, ensure that the power cable used meets all appli-
cable standards for the country in which it is to be installed.

For AC powered devices which have 3 conductor power plugs (L1, L2 & 
GND or Hot, Neutral & Safety/Protective Ground), the wall outlet (or 
socket) must have an earth ground.

For DC powered devices, ensure that the interconnecting cables are rated 
for proper voltage, current, anticipated temperature, flammability, and 
mechanical serviceability.

WAN, LAN & PSTN ports (connections) may have hazardous voltages 
present regardless of whether the device is powered ON or OFF.  PSTN 
relates to interfaces such as telephone lines, FXS, FXO, DSL, xDSL, T1, E1, 
ISDN, Voice, etc. These are known as “hazardous network voltages” and 
to avoid electric shock use caution when working near these ports.  When 
disconnecting cables for these ports, detach the far end connection first.

Do not work on the device or connect or disconnect cables during periods of 
lightning activity

This device contains no user serviceable parts.  This device can only be 
repaired by qualified service personnel.

In accordance with the requirements of council directive 2002/
96/EC on Waste of Electrical and Electronic Equipment (WEEE), 
ensure that at end-of-life you separate this product from other 
waste and scrap and deliver to the WEEE collection system in 
your country for recycling.

WARNING

WARNING

Содержание SMARTNODE 4940




























































Отзывы: