Patton electronics 3092 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 162

background image

14 • RIP Version 2

! "#

96

&; 7D! ,

Domain (rip2IfConfDomain)

Value inserted into the

,

field of all RIP packets sent on this interface.

Authentication Type (rip2IfConfAuthType)

The type of Authentication used on this interface.

•

noAuthentication (1)

•

simplePassword (2)

Authentication Key (rip2IfConfAuthKey)

This value is used as the Authentication Key whenever

%2 7&! %3

has a value

other than noAuthentication(1). A modification of

%

does not change the value of

F%

. If the Authentication Key string is shorter than 16 octets, it will be left justified, then padded to 16

octets with nulls (0x00) on the right.

Reading this object always results in an octet string of length zero. Authentication may not be bypassed by
reading the MIB object.

Send (rip2IfConfSend)

is what the router sends on this interface. ripVersion 1 implies sending RIP updates compliant with RFC

1058. There are four options,

) "* "#"$

and

"* '

.

rip1Compatible implies broadcasting RIP-2 updates using RFC 1058 route subsumption rules. ripVersion2
implies multicasting RIP-2 updates. ripV1Demand indicates the use of Demand RIP on a WAN interface
under RIP Version 1 rules. ripV2Demand indicates the use of Demand RIP on a WAN interface under Version
2 rules.

•

doNotSend (1)

•

ripVersion1 (2)

•

rip1Compatible (3)—rip1Compatible implies broadcasting RIP-2 updates using RFC 1058 route sub-
sumption rules

•

ripVersion2 (4)—ripVersion2 implies multicasting RIP-2 updates

Receive (rip2IfConfReceive)

This indicates which version of RIP updates are to be accepted. Note that

"

and

"+ "

implies recep-

tion of multicast packets.

•

rip1 (1)

•

rip2 (2)

•

rip1OrRip2 (3)

•

doNotRecieve (4)

Metric (rip2IfConfDefaultMetric)

This variable indicates the metric that is to be used for the default route entry in RIP updates originated on this
interface. A value of zero indicates that no default route should be originated; in this case, a default route via
another router may be propagated.

«
...
96
97
98
99
100
...
»

Содержание 3092



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3092

Бренд: TC Electronic Страницы: 174

Finalizer Express

Бренд: TC Electronic Страницы: 33

Бренд: Dahua Страницы: 6

Бренд: NETGEAR Страницы: 14

OCTOPUS 5TX-EEC

Бренд: Hirschmann Страницы: 6

Бренд: Baldor Страницы: 34

PARTNER PC CARD

Бренд: Avaya Страницы: 4

Бренд: ebm-papst Страницы: 11

Бренд: YASKAWA Страницы: 15

Бренд: DAD Страницы: 16

Бренд: Addonics Technologies Страницы: 1

NetIron MLXe Series

Бренд: Brocade Communications Systems Страницы: 305

Бренд: TP-Link Страницы: 2

Бренд: Idis Страницы: 20

UniFi LED ULED-AT

Бренд: Ubiquiti Страницы: 16

Бренд: ZyXEL Communications Страницы: 2

Бренд: DIGIWEB Страницы: 16

Бренд: Ubiquiti Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды