Patton electronics 3092 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 162

background image

9 • Filter IP

! "#

62

,

The following sections provide detailed descriptions of the configurable filter IP parameters.

Name (filterIpName)

This is the name of the filter

Direction (filterIpDirection)

Specifies the direction of the filter (that is, whether it applies to data packets inbound or outbound from the
DACS). The filter only applies to the Superuser and the Monitor Users through the Ethernet interface. (Since
the iDSL modem and WAN connections function as a transparent pipe, neither of the two users can utilize
these interfaces, only the Ethernet interface.) The following options are available:

•

inactive(0)—Disables filter operation

•

inbound(1)—Relates to packets coming into the DACS

•

outbound(2)—Relates to packets leaving the DACS

•

both(3)—Specifies both inbound and outbound operation

Action (filterIpAction)

Specifies the action to effect the packet. The action decides whether to block or pass the packet. The following
options are available:

•

pass(0)—If pass is selected, checking will continue on to other filters until either a match occurs, a block
occurs, or there are no more filters remaining to check.

Note

If there are any applied PASS filters, then at least one of them must
match or the packet will be dropped.

•

block(1)—If a filter has block set and the filter matches the block, the packet is discarded and no further
processing is done.

•

wrap(2)—All packets received on the specified link will be encapsulated in an extra IP header as defined in
RFC2003. The destination IP address of the wrapper is given by the destination IP setting in the filter. The
source IP address of the wrapper is the ethernet address of the DACS.

All wrap filters are inbound only.

Source IP (filterIpSourceIp)

This is the Source IP address in the IP header, it is used when comparing a packet’s source address.

Source IP Mask (filterIpSourceMask)

This is the Source IP Mask (filterIpSourceMask) used when comparing a packet’s source address. Bit positions
that are set to 1 will be compared and 0’s will be ignored. Thus, a setting of 0.0.0.0 will have the effect of dis-
abling source IP address comparison.

Destination IP (filterIpDestinationIp)

This is the destination IP address in the IP header used when comparing a packet’s destination address.

«
...
62
63
64
65
66
...
»

Содержание 3092



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3092

Бренд: H3C Страницы: 1057

Бренд: Paradyne Страницы: 22

Бренд: ICP DAS USA Страницы: 14

Бренд: ICP DAS USA Страницы: 25

Бренд: ICP DAS USA Страницы: 15

Бренд: ICP DAS USA Страницы: 8

Бренд: ICP Страницы: 14

QSR-3920 Series

Бренд: QTech Страницы: 120

Бренд: QSC Страницы: 28

Transportation FiberinMotion

Бренд: Radwin Страницы: 122

Бренд: SAF Страницы: 30

Бренд: ebm-papst Страницы: 16

Adapter Bracket

Бренд: Paradyne Страницы: 1

Бренд: Paradyne Страницы: 85

Converter Board R0E5212BACFG00

Бренд: Renesas Страницы: 6

Бренд: ZyXEL Communications Страницы: 5

RealPort Ethernet 10/100

Бренд: Xircom Страницы: 30

Бренд: Tektronix Страницы: 178

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды