Patton electronics 3092 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 162

background image

& ( (

73

! "#

11 • IP

Note

The Discarded w/No Errors counter does not include any datagrams
discarded while awaiting re-assembly.

Total Deliveries (ipInDelivers)

The total number of input datagrams successfully delivered to IP user-protocols (including ICMP).

Out Requests (ipOutRequests)

The total number of IP datagrams which local IP user-protocols (including ICMP) supplied to IP in requests
for transmission.

Note

The Out Requests counter does not include any datagrams counted
in ipForwDatagrams.

Out Discards (ipOutDiscards)

The number of output IP datagrams for which no problem was encountered to prevent their transmission to
their destination, but which were discarded (e.g., for lack of buffer space).

Note

The Out Discards counter would include datagrams counted in
ipForwDatagrams if any such packets met this (discretionary) discard
criterion.

Discarded for No Routes (ipOutNoRoutes)

The number of IP datagrams discarded because no route could be found to transmit them to their destination.

Note

The Discarded for No Routes counter includes any packets counted
in ipForwDatagrams which meet this “no-route” criterion. This
includes any datagrams which a host cannot route because all of its
default gateways are down.

Reassembly Timeout (ipReasmTimeout)

The maximum number of seconds which received fragments are held while they are awaiting reassembly at this
entity.

# of Reassembled Fragments (ipReasmReqds)

The number of IP fragments received which needed to be reassembled at this entity.

# Successfully Reassembled (ipReasmOKs)

The number of IP datagrams successfully reassembled.

Reassembly Failures (ipReasmFails)

The number of failures detected by the IP reassembly algorithm (for whatever reason: timed out, errors, etc).

Note

The Reassembly Failures value is not necessarily a count of discarded
IP fragments since some algorithms (notably the algorithm in
RFC 815) can lose track of the number of fragments by combining
them as they are received.

«
...
73
74
75
76
77
...
»

Содержание 3092



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3092

Бренд: NEC Страницы: 10

Бренд: NEC Страницы: 8

Бренд: IEI Technology Страницы: 19

Бренд: IEI Technology Страницы: 87

Бренд: IEI Technology Страницы: 3

grandMA2 Series

Бренд: MA lighting Страницы: 36

Бренд: Octavo Страницы: 28

Бренд: Obihai Страницы: 2

Бренд: Paradox Страницы: 4

Бренд: Tripp Lite Страницы: 20

Бренд: NETGEAR Страницы: 84

Бренд: IDT Страницы: 207

Бренд: Cisco MERAKI Страницы: 4

Бренд: Rajant Corporation Страницы: 40

Бренд: Pakedge Device & Software Страницы: 14

500 - DATASHEET REV 003

Бренд: Intel Страницы: 67

Бренд: Quadram Страницы: 21

Blue Gate ISDN BRI Brave

Бренд: Alphatech Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды