manualshive.com logo in svg
background image

45

APPENDIX B

PATTON NETLINK-T1™ MODEL 2710RC

CABLE RECOMMENDATIONS

The Patton NetLink T1™ Series has been performance tested by

Patton technicians using twisted-pair cable with the following charac-
teristics:

Wire Gauge

Capacitance

Resistance

19 AWG

83nf/mi or 15.72 pf/ft.

.0163 Ohms/ft.

22 AWG

83nf/mi or 15.72 pf/ft.

.0326 Ohms/ft.

24 AWG

83nf/mi or 15.72 pf/ft.

.05165 Ohms/ft.

To gain optimum performance from the Model 2710RC Series,

please keep the following guidelines in mind:

• 

Always use twisted pair wire—this is not an option.

• Use twisted pair wire with a capacitance of 20pf/ft or less.

• Avoid twisted pair wire thinner than 26 AWG (i.e. avoid AWG
numbers higher than 26)

• Use of twisted pair with a resistance greater than the above
specifications may cause a reduction in maximum distance obtain-
able.  Functionality should not be affected.

• Many environmental factors can affect the maximum distance
obtainable at a particular site. 

46

APPENDIX C

PATTON NETLINK-T1™ MODEL 2710RC

FACTORY REPLACEMENT PARTS

AND ACCESSORIES

Patton Model #

Description

2710RC/D/V

T1/FT1 CSU/DSU Rack Card, X.21
Interface w/DB15FS/RJ48C rear card

2710RC/B/B

T1/FT1 CSU/DSU Rack Card, RS530
Interface with DB25F/RJ48C Rear Card

2710RC/A/I

T1/FT1 CSU/DSU Rack Card, V.35
Interface with M/34F/RJ48C Rear Card

1001RPEM-RAC

120/240V Rear Power Entry Module

1001RPEM-RAC

120/240V Rear Power Entry Module

1001RPSM-RUI

120/240V Front Power Supply Module

1001RPEM-RDC

DC Rear Power Entry Module

1001RPSM-R48A

48V Front Power Supply Module

1001R14P

Rack 14 Slot 2U Chassis Only

1001R14P/R48V

Rack 14 Slot 2U w/Dual Universal Input
48VDC Power Supplies

1001R14P/RUIA

Rack 14 Slot 2U w/Dual Universal Input
90-260VAC Power Supplies 
European Power Cord

1001R14P/RUIC

Rack 14 Slot 2U w/Dual Universal Input
90-260VAC Power Supplies
Austrialia Power Cord

1001R14P/RUID

Rack 14 Slot 2U w/Dual Universal Input
90-260VAC Power Supplies
UK Power Cord

1001R14P/RUIG

Rack 14 Slot 2U w/Dual Universal Input
90-260VAC Power Supplies
India Power Cord

1001R14P/RUIK

Rack 14 Slot 2U w/Dual Universal Input
90-260VAC Power Supplies
US Power Cord

1001RCM12548C

DB-25/RJ-45 Rear Card

1001RCM13448C

M/34/RJ-45 Rear Card

1001CC

Control Card

IM2RC/B

RS-530 Interface Rear Card

1180RC DB

V.35 Daughter Board

05R16BP440W

Single Width Blank Rear Panel, White

05R16FP440W

Single Width Blank Front Panel, White

0516FPB1

Single Width Blank Front Panel, Black

0516FPB4

4-Wide Blank Front Panel, Black

0516RPB1

Single Width Blank Rear Panel, Black

0516RPB4

4-Wide Blank Rear Panel, Black

056S1

Set of 16 #4 pan head screws/washers

10-25M/35M-1

Cable, 6 ft, DB-25 male to M/34 male

1010-10

Terminal Block, 2 Position, Male

07M2710RC

User Manual

Содержание 2710RC Series



























Отзывы: