background image

21

22

APPENDIX B

PATTON ELECTRONICS MODEL 1004ARC

CABLE RECOMMENDATIONS

The Patton Model 1004ARC operates at frequencies of 60kHz or

less and has been performance tested by Patton technicians using
twisted-pair cable with the following characteristics:

Wire Gauge

Capacitance

Resistance

19 AWG

83nf/mi or 15.72 pf/ft.

.0163 Ohms/ft.

22 AWG

83nf/mi or 15.72 pf/ft.

.0326 Ohms/ft.

24 AWG

83nf/mi or 15.72 pf/ft.

.05165 Ohms/ft.

Using or simulating cable with the above characteristics, the follow-

ing data rate/distance results were obtained by Patton during bench
tests:

To gain optimum performance from the Model 1004ARC, please keep
the following guidelines in mind:

• 

Always use twisted pair wire—this is not an option.

• Use twisted pair wire with a capacitance of  20pf/ft or less.

• Avoid twisted pair wire thinner than 26 AWG (i.e. avoid higher

AWG numbers than 26)

• Use of twisted pair with a resistance greater than the above speci-

fications may cause a reduction in maximum distance obtainable.
Functionality should not be affected.

• Many environmental factors can affect the maximum distances

obtainable at a particular site. Use the above data rate/distance
table as a 

general guideline only.

APPENDIX C

PATTON ELECTRONICS MODEL 1004ARC 

FACTORY REPLACEMENT PARTS

The Patton Model 1004ARC rack system features interchangeable

rear half cards, power cords/fuses for international various operating
environments and other user-replaceable parts. Model numbers and
descriptions for these parts are listed below:

Patton Model #

Description

1000RPEM..........................120/240V Rear Power Entry Module
1000RPSM-2.......................120/240V Front Power Supply Module
1000RPEM-DC ...................DC Rear Power Entry Module
1000RPSM-48A ..................48V Front Power Supply Module
1000RPEM-V ......................120/240V CE Compliant Rear Power 

Entry Module

1000RPEM-V ......................120/240V CE Compliant Rear Power 

Supply Entry Module

0805US ...............................American Power Cord
0805EUR.............................European Power Cord CEE 7
0805UK ...............................United Kingdom Power Cord
0805AUS .............................Australia/New Zealand Power Cord
0805DEN.............................Denmark Power Cord
0805FR ...............................France/Belgium Power Cord
0805IN.................................India Power Cord
0805IS.................................Israel Power Cord
0805JAP..............................Japan Power Cord
0805SW ..............................Switzerland Power Cord

0516FPB1 ...........................Single Width Blank Front Panel
0516FPB4 ...........................4-Wide Blank Front Panel
0516RPB1...........................Single Width Blank Rear Panel
0516RPB4...........................4-Wide Blank Rear Panel

MODEL 1004ARC Distance Table- Miles (Km)

Data Rate

Wire Gauge

(kbps)

19

22

24

26

115.2

3.5 

(5.6)

2.6 

(4.2)

1.4 

(5.6)

0.9 

(1.4)

38.4

5.0 

( 8.0)

2.9 

(4.7)

2.2 

(3.5)

1.5

(2.4)

9.6

7.1 

(11.4)

4.6 

(7.4)

3.5 

(5.6)

2.8 

(4.5)

1.2

9.0 

(14.5)

6.5 

(10.5)

5.0 

(8.0)

3.9 

(6.3)

Содержание 1004ARC














Отзывы: