background image

3

4

1.2  CE NOTICE

The CE symbol on your Patton Electronics equipment indicates

that it is in compliance with the Electromagnetic Compatibility (EMC)
directive and the Low Voltage Directive (LVD) of the Union European
(EU). A Certificate of Compliance is available by contacting Technical
Support.

1.3  SERVICE

All warranty and non-warranty repairs must be returned freight pre-

paid and insured to Patton Electronics. All returns must have a Return
Materials Authorization number on the outside of the shipping contain-
er. This number may be obtained from Patton Electronics Technical
Support:

Tel:

(301) 975-1007 

Email: [email protected].
www: http://www.patton.com

Patton Electronics' technical staff is also available to answer any

questions that might arise concerning the installation or use of your
Model 1004ARC. Technical Service hours: 8AM to 5PM EST, Monday
through Friday.

2.0  GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product.

This product has been thoroughly inspected and tested and is warrant-
ed for One Year parts and labor. If any questions during installation or
use of the 1004ARC, contact Patton Electronics Technical Support at
(301) 975-1007.

2.1  FEATURES

• Convenient rack card features two short range modems 

• Data rates to 115.2 Kbps 

• Supports up to 50 multipoint device drops in a polling environ-

ment

• Passes transmit & receive data, one control signal each direction

• Variable high/low impedance settings

• Carrier can be set as “constantly on” or “controlled by RTS”

• Able to operate with or without “echo”

• Features 6 easy-to-read LEDs 

• Silicon Avalanche Diode surge protection

• Fits conveniently in Patton’s rack chassis

2.2  DESCRIPTION

The Model 1004ARC high speed, multipoint short range modem

rack card is a 

dual rack card incorporating two short range modems.

Both units support asynchronous data rates to 115.2 Kbps over 1 or 2
twisted pairs and support distances to 9.4 miles (19 AWG @19.2
kbps). The Model 1004ARC features 6 easy-to-read front panel LEDs
and incorporates Silicon Avalanche Diodes for protection against the
damaging effects of nearby lightning strikes and other harmful tran-
sients.

The Model 1004ARC can handle up to 50 terminal drops in a mul-

tipoint polling environment. For RS-485 and serial printer applications
requiring hardware handshaking, the Model 1004ARC passes one con-
trol signal in each direction. The Model 1004ARC may be configured
for high or low impedance operation, carrier may be set to “constantly
on” or “controlled by RTS”, and the unit can operate with or without
“echo”. RTS/CTS delay may be set for “no delay” or 8 mS.

Filling one function card slot on Patton’s Model 1000R16 rack

chassis, the Model 1004ARC is available with RJ-11 or RJ-45 rear
interface cards. For workgroup and desktop communications, the
Model 1004ARC also fits in Patton’s 2, 4 and 8 slot ClusterBoxes™.
The combination of rack mount, ClusterBox™ and self-powered units
provides a completely integrated Model 1004A “networking” solution.

NOTE:

Packages received without an RMA number will not be

accepted.

Содержание 1004ARC














Отзывы: