Patterson-Kelley P-K STORM ST-1250 Скачать руководство пользователя

Страница: 57 / 95

P-K Storm

Gas Fired Boiler

Technical Service 1.877.728.5351

Revised: October 2, 2019
Released: October 2, 2019



Patterson-Kelley 2019

2691000099 P-K Storm Installation and Owners

Manual.docx

Page 48

Home Screen

After a brief time, the

Local Representative

information screen will

timeout displaying the

Home Screen

. The

Home Screen

shows a

snapshot of the boiler or water heater’s current operating conditions:

•

Outlet (Supply) Temperature

•

Inlet (Return) Temperature

•

Exhaust Temperature

•

Firing Rate, etc.

Pressing the

“Info”

button in the lower left corner will load the

Information

screen.

For the setup wizard, press the

“Settings”

button in the lower right

corner to load the “

Settings”

“Main Menu”

screen.

Information Screen

The Information Screen contains real-time read-only values such as
temperatures, relay states, etc. Scroll through the Information Screen
by sliding your finger up or down. This screen is helpful to determine
the operating characteristics.

NOTE

For more information on any value, please refer
to the NURO

Boiler Controller: Advanced User’s

Guide, Part Number is 1004905979.

Содержание P-K STORM ST-1250
































































































Результаты поиска

Содержание P-K STORM ST-1250

Отзывы:

Похожие инструкции для P-K STORM ST-1250

Бренды по названию

Популярные бренды

Patterson-Kelley P-K STORM ST-1250, Инструкция по установке и эксплуатации

Результаты поиска

Содержание P-K STORM ST-1250

Отзывы:

Похожие инструкции для P-K STORM ST-1250

Бренды по названию

Популярные бренды