53
General Specifications
（
01
）
Buzzer sound No.4 was measured from the total circumference of the Buzzer Unit at 1m
Buzzer Unit
：
90mA (
※
1)
LED Unit
：
90mA
Buzzer Unit
：
1.1W (
※
1)
LED Unit
：
1W
LED Unit
：
1.1W
Buzzer Unit
：
1.2W (
※
1)
500VAC applied for 1min Between live part and non-current carrying metallic part without breaking insulation
60±2 Flashes Per Minute
Upright
Upright
IP65(IEC 60529) / NEMA TYPE 4X,13
IP54(IEC 60529) / NEMA TYPE 4X,13
0.7A / Less than 15ms
0.38kg + (0.04kg)×Tiers + [0.05kg]
0.49kg + (0.04kg)×Tiers + [0.05kg]
0.2kg + (0.04kg)×Tiers + [0.05kg]
(LED Unit) + [Buzzer Unit]
Typ.80dB
Refer to Section 3 “
Part Names and Outer Appearance”
More than 1M
Ω
at 500VDC between live part and non-current carrying metallic part
Buzzer Unit
：
250mA (
※
1)
LED Unit
：
100mA
-20
℃
〜
+50
℃
Less than 90% RH (No Condensation)
-30
℃
〜
+60
℃
Less than 90% RH (No Condensation)
Indoor Only
LR5-
□
01
□□□
W
Buzzer Unit
：
none (Not exceeding Maximum Signal Wire Current Ratings) (
※
2)
LED Unit
：
none (
※
2)
LED Unit
：
none
Buzzer Unit
：
0.3W
Body Unit
：
0.1W
No.1
PJ
LJ
WJ
No.2
No.3
No.4
Rapid Intermittent Beep / 3378Hz
Continuous Beep Sound / 3378Hz
Rapid Hi-Lo / 2016Hz&3012Hz
Depending on DIP Switch settings.
Refer to Section 6 “Buzzer Pattern Set-up”.
Sweep Sound / 1000Hz-4032Hz
Max.
Operating Voltage Range
Typ.
Signal Wire Current
Rated Voltage
（
Per Unit
）
Rated Power
Consumption
（
Per Unit
）
Inrush Current
Mounting Direction
Environmental Condition
Environmental Condition
Setting
Insulation Resistance
Outer Dimensions
Buzzer Sound/
Typical Frequency
Operating Ambient Temperature
Operating Ambient Humidity
Storage Ambient Temperature
Storage Ambient Humidity
Mounting Location
Protection Rating
Withstand Voltage
Flashing Rate
Model
Power Supply Wire
Signal Wire
Standby Power Consumption
Max.
Typ.
Mass
(Tolerance ±10%)
Sound Pressure Level
Conformity Standards
Remarks
12V DC
Rated Voltage ±10%
UL 508, CSA-C22.2 No. 14, EMC Directive (EN 61000-6-4, EN 61000-6-2)
RoHS Directive (EN 50581), FCC Part 15 Subpart B Class A
KC (KN 61000-6-4, KN 61000-6-2)
(
※
1) Environmental Condition: Buzzer sound No.2 (Continuous Beep Sound)
(
※
2)When (Gray) power supply wire is not connected, inrush current or 0.7A will flow through the
signal wires.
●
This product is designed for use on a flat surface for a
Type 1 Enclosure
.
(Conformity requirements for UL Standard)
●
Use a "
class 2
" power supply specified in the guidelines under
UL1310
. (Conformity requirements for UL Standard)
●
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These restrictions are limited to cases where this equipment is operated in a business district, and it is designed to take the
relevant protective measures against electromagnetic noise hindrance.
●
This product must not be used in residential areas. (Conformity requirements for the CE Marking)
Sound Reduction approximately -10dB,
depending on DIP Switch settings.
Refer to Section 6 “Buzzer Pattern Set-up”
Due to the characteristics of the LED elements, a variation in difference of the color tone and brightness
of every product may occur.
UL Recognized Component (File No.E215660)
LJ
ghv Vertriebs-GmbH
| Am Schammacher Feld 47 | 85567 Grafing | T 49 80 92 81 89 0 | [email protected] |
www.ghv.de
