PAT DS 350 / 1334 GRAPHIC Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 51

PAT DS 350 / 1334 GRAPHIC Скачать руководство пользователя страница 47

Pre-Operation Inspection and Calibration Verification

43

If  any  of  the  displays  reflects  a  deviation  between  displayed  and  actual  values,  an  authorized
PAT  service  representative  shall  be  called  for  repair  of  the  system  or  re-verification  of    the
crane’s RCL  calibration.

Any structural modifications or changes to the crane shall require re-

verification of the crane’s RCL

calibration.

7. Check that the display of the operating radius of the crane agrees with the actual radius.

8. Check the load display by lifting a load of known weight.

Operation

Upon correct inspection the RCL is operational. The operator shall be thoroughly familiar with all
controls of the RCL before operating the crane. The proper function of the system shall be
checked by lifting a load of known weight and comparing the load to the information displayed
on the RCL.

Rated loads include the weight of the hook block, slings, and auxiliary load handling devices.
Their combined weights shall be subtracted from the listed load capacities as stated on the load
capacity chart to obtain the net load to be lifted.

«
...
45
46
47
48
49
...
»

Содержание DS 350 / 1334 GRAPHIC




















































Отзывы:

Нет отзывов