PAT DS 350 / 1334 GRAPHIC Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 51

PAT DS 350 / 1334 GRAPHIC Скачать руководство пользователя страница 14

System Description

1
1

The correct setting is of utmost importance for the proper functioning of the system and the
crane. Therefore, only operators who are thoroughly familiar with the crane and the operation
of the system should execute the setting of the system according to the operating
configuration of the crane.

4

CONFIGURATION SETUP

The RCL setup procedure allows the operator to input the crane configuration using interactive
displays. The operator must complete the configuration setup procedure for the Rated Capacity
Limiter system by confirming (pressing OK) to set the system into operation or deleted (pressing DEL)
to enter a new configuration. The previous configuration setup will be displayed shown in bold
symbols and must match the current crane operating configuration.

RCL Setup Procedure

...starts:



manually

after each modification of the crane configuration by

pressing "SEL" (9) button.

...is operated:



by answering the different questions using functional buttons
F1...F4 in accordance with the actual configuration of the crane.

...is cancelled:



any time by pressing again the "SEL" (9) button. The system,
however, is only ready for operation, if the procedure has been
completed and the selections have been confirmed.

If the system is turned off, all adjustments remain stored. When turning the system on again these
adjustments can be acknowledged by merely pressing the OK button (provided that the crane
configuration has not been modified!).

During the programming procedure the Rated Capacity Prewarning Light (3) and the Rated
Capacity Limiter Light (2) will light up and the crane functions will be interrupted.

Note:

If a configuration is selected which is not available, the display will indicate error code E04.

In this case, the procedure has to be repeated with valid values!

«
...
12
13
14
15
16
...
»

Содержание DS 350 / 1334 GRAPHIC




















































Отзывы:

Нет отзывов