9
10
Binding is the process of programming the receiver of the control unit to
recognize the GUID (Globally Unique Identifier) code of a single specific
transmitter. It will be necessary for you to ‘bind’ your chosen Spektrum DSM2
technology equipped transmitter to the receiver for proper operation.
The following is a list of some of the Spektrum DSM2 equipped transmitters
and modules that will bind to the receiver of the Sukhoi:
Note: ParkZone recommends flying the fully aerobatic Sukhoi with a full
size transmitter equipped with dual rates.
E-flite HP6DSM
Spektrum DX5e
Spektrum DX6i
Spektrum DX7
JR X9303 2.4
JR 12X 2.4
Note: The Spektrum DX6 (SPM2460) is equipped with DSM (not DSM2)
technology and is not compatible with the receiver of the
Sukhoi BNF.
The following steps outline the binding process:
• Confirm the process of entering the bind mode for your chosen
transmitter by reviewing the instruction manual included with
the transmitter.
• Make sure the flight battery is disconnected from the receiver unit and
the transmitter is turned off.
• Plug the flight battery into the receiver unit. After 5 seconds the LED on
the receiver unit will begin flashing.
• After verifying the LED is flashing on the receiver, follow the steps that
allow your chosen transmitter to enter bind mode.
• If you entered bind mode correctly, you will see a solid LED
approximately 5–10 seconds later on the receiver. You should now be
bound to the transmitter, and have full control and function.
If you encounter any problems, repeat the binding process again, see the
trouble shooting guide or call the Horizon Support Team at 1-877-504-0233.
Transmitter and Receiver Binding
Transmitter Specific Binding Instructions
Compatible, but not recommended:
ParkZone Vapor Transmitter
E-flite LP5DSM
E-flite MLP4DSM
DX5e:
A. To bind your Sukhoi Su-26m to the DX5e, plug the battery into the
receiver of the airplane. The LED on the receiver will begin flashing.
B. Move the sticks and switches on the transmitter to the desired failsafe
positions (low throttle and neutral control positions).
C. Pull and hold the Trainer Switch on the transmitter while turning the
transmitter on. Release the trainer switch once the LEDs on the front
of the transmitter flash.
D. The LED on the receiver will go solid red and the system will connect
after several seconds.
DX6i:
A. To bind your Sukhoi Su-26m to the DX6i, plug the battery into the
receiver of the airplane. The LED on the receiver will begin flashing.
B. Move the sticks and switches on the transmitter to the desired failsafe
positions (low throttle and neutral control positions).
C. Pull and hold the Trainer Switch on the transmitter while turning the
transmitter on. Release the trainer switch once the word BIND flashes
on the LCD screen on the front of the transmitter.
D. The LED on the receiver will go solid red and the system will connect
after several seconds.
DX7 (includes DX7se):
A. To bind your Sukhoi Su-26m to the DX7, plug the battery into the
receiver of the airplane. The LED on the receiver will begin flashing.
B. Move the sticks and switches on the transmitter to the desired failsafe
positions (low throttle and neutral control positions).
C. Press the bind button on the back of the transmitter while turning the
transmitter on. The bind button on the back of the transmitter will flash.
Release the button after 2-3 seconds.
D. The LED on the receiver will go solid red and the system will connect
after several seconds.
X9303:
A. To bind your Sukhoi Su-26m to the X9303, plug the battery into the
receiver of the airplane. The LED on the receiver will begin flashing.
B. Move the sticks and switches on the transmitter to the desired failsafe
positions (low throttle and neutral control positions).
C. Press the bind button on the back of the transmitter while turning the
transmitter on. The bind button on the back of the transmitter will flash.
Release the button after 2-3 seconds.
D. The LED on the receiver will go solid red and the system will connect
after several seconds.
