Parkside 273098, Руководство по эксплуатации и технике безопасности

Страница: 14 / 64

9 GB/IE
8.4 Cross cut 90° and turntable 0° - 45° (Fig. 9)
The crosscut saw can be used to make crosscuts of 0°
-45° to the left and 0° -45° to the right in relation to the
stop rail.
Important . To make 90° crosscuts, the adjustable stop
UDLODPXVWEH¿[HGDWWKHLQQHUSRVLWLRQ
• Open the set screw (16b) for the adjustable stop rail
and push the adjustable stop rail inwards.
•
7KHDGMXVWDEOHVWRSUDLOPXVWEH¿[HGIDU
enough in front of the innermost position that the
distance between the stop rail (16a) and the saw
blade (6) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (16a)
and the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Loosen set screw (26).
• Use the handle (11) to adjust the rotary table (14)
to the desired angle. The pointer (12) on the rotary
table must match the desired angle on the scale (13)
RQWKH¿[HGVDZWDEOH
• Re-tighten the set screw (26) in order to secure the
rotary table (14).
• Cut as described under section 8.3.
8.5 Precision adjustment of the stop for mitre cut
45° (Fig. 1/10/11)
• No stop angle included.
• Lower the machine head (4) and secure using the
locking bolt (23).
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22) and use the handle (1) to
angle the machine head (4) 45° to the left.
• 45° - position angle stop (b) between the saw blade
(6) and rotary table (14).
• Adjust the adjusting screw (28) until the angle be-
tween the saw blade (6) and rotary table (14) is pre-
cisely 45°.
•
,WLVQRWQHFHVVDU\WR¿[WKLVVHWWLQJEHFDXVHLWLV
maintained by the spring pretension.
• Subsequently check the position of the angle indi-
cator. If necessary loosen the pointer (19) using a
Philips screwdriver, set to position 45° on the angle
scale (18) and re-tighten the retaining screw.
8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1/2/12)
The crosscut saw can be used to make mitre cuts of
0° - 45° in relation to the work face.
Important . To make miter cuts (inclined saw head),
WKHDGMXVWDEOHVWRSUDLODPXVWEH¿[HGDWWKHRXWHU
position.
• Open the set screw (16b) for the adjustable stop rail
(16a) and push the adjustable stop rail outwards.
•
7KHDGMXVWDEOHVWRSUDLODPXVWEH¿[HGIDU
enough in front of the innermost position that the
distance between the stop rail (16a) and the saw
blade (6) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (16a)
and the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22) and use the handle (1)
to angle the machine head (4) to the left, until the
pointer (19) indicates the desired angle measure-
ment on the scale (18).
•
5HWLJKWHQWKH¿[LQJVFUHZ
• Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°
(Fig. 2/4/13)
The crosscut saw can be used to make mitre cuts to
the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° to the left or 0° - 45° to the
right in relation to the stop rail (double mitre cut).
Important . To make miter cuts (inclined saw head),
WKHDGMXVWDEOHVWRSUDLODPXVWEH¿[HGDWWKHRXWHU
position.
• Open the set screw (16b) for the adjustable stop rail
(16a) and push the adjustable stop rail outwards.
•
7KHDGMXVWDEOHVWRSUDLODPXVWEH¿[HGIDU
enough in front of the innermost position that the
distance between the stop rail (16a) and the saw
blade (6) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (16a)
and the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to its upper position.
• Release the rotary table (14) by loosening the set
screw (26).
• Using the handle (11), set the rotary table (14) to the
desired angle (refer also to point 8.4 in this regard).
• Re-tighten the set screw (26) in order to secure the
rotary table.
• Undo the locking screw (22) and use the handle (1)
to tilt the machine head (4) to the left until it coin-
cides with the required angle value (in this connec-
tion see also section 8.6).
•
5HWLJKWHQWKH¿[LQJVFUHZ
• Cut as described under section 8.3.
8.8 Limiting the cutting depth (Fig. 3/14)
•
7KHFXWWLQJGHSWKFDQEHLQ¿QLWHO\DGMXVWHGXVLQJWKH
screw (24). To do this loosen the knurled nut on the
screw (24). Move the stop for the cutting depth limi-
tre (25) to the outside. Turn the screw (24) in or out
to set the required cutting depth. Then re-tighten the
knurled nut on the screw (24).
• Check the setting by completing a test cut.
8.9 Sawdust bag (Fig. 1)
The saw is equipped with a debris bag (17) for saw-
dust and chips.
Squeeze together the metal ring on the dust bag and
attach it to the outlet opening in the motor area.
The debris bag (17) can be emptied by means of a zip-
per at the bottom.
8.10 Changing the saw blade (Fig. 15/16/17/18)
Remove the power plug!
Important.
Wear safety gloves when changing the saw blade.
Risk of injury!