Parkside Performance PAKSP 20-Li A1, Перевод оригинальной инструкции

Страница: 19 / 39

GB │ MT │
15 ■
PAKSP 20-Li A1
Technical specifications
Cordless mitre saw PAKSP 20-Li A1
Rated voltage 20 V (DC)
Rated idle speed n
0
4300 rpm
Max. cutting width/depth at 90 x 90° 120 x 60 mm
90 x 45° 80 x 60 mm
45 x 90° 120 x 35 mm
45 x 45° 80 x 35 mm (right)
45 x 45° 60 x 35 mm (left)
Pivoting range (table) - 45°/+ 45°
Mitre cut 0–45° to the left
Saw blade
210 mm
Ø 210 x 30 mm, 48 teeth,
Tooth width: max. 2 mm
Battery PAP 20 A3
Type LITHIUM ION
Rated voltage 20 V (DC)
Capacity 4 Ah (80 Wh)
Cells 10
High-speed battery charger PLG 20 A3
INPUT
Rated voltage 230–240 V ∼ (AC), 50 Hz
Rated power consumption: 120 W
Fuse (internal) 3.15 A
T3.15A
OUTPUT
Rated voltage 21.5 V (DC)
Rated current 4.5 A
Charging time approx. 60 min.
Protection class II / (double insulation)
Wear ear muffs!
Read the operating
instructions before use!
Noise emission value
Noise measurement value determined in accordance with EN 62841.
The A-rated noise level of the power tool is typically:
Sound pressure level
L
PA
= 83.2 dB (A)
Uncertainty K K
PA
= 3 dB
Sound power level L
WA
= 94.2 dB (A)
Uncertainty K K
WA
= 3 dB
Wear ear muffs!
Vibration emission value
Total vibration values (vector total of three directions) determined in
accordance with EN 62841:
Sawing wood
a
h,W
= 2.03 m/s 2
Uncertainty K = 1.5 m/s 2
NOTE
► The vibration emission values and the noise emission values given in
these instructions have been measured in accordance with a standard-
ised test procedure and can be used for comparison of the power
tool with another tool.
► The specified total vibration values and the noise emission values can
also be used to make a provisional load estimate.
WARNING!
► Depending on the manner in which the power tool is being used, and
in particular the kind of workpiece being worked, the vibration and
noise emission values can deviate from the values given in these
instructions during actual use of the power tool.
► Try to keep the vibration load as low as possible. Measures to reduce
the vibration load are, e.g. wearing gloves and limiting the working
time. Wherein all states of operation must be included (e.g. times
when the power tool is switched off and times where the power tool is
switched on but running without load).
General power tool safety warnings
WARNING!
►
Read all safety warnings, instructions, illustrations and specifica-
tions provided with this power tool.
Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as in
the presence of flammable liquids, gases or dust.
Power tools create
sparks which may ignite the dust or fumes.
c)
Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power
tools.
Unmodified plugs and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators.
There is an increased risk
of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering
a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts.
Damaged or entangled cords increase the risk
of electric shock.
e) When working outdoors with an electrical power tool always use
extension cords that are also suitable for use outdoors.
Use of a
cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use
a residual current device (RCD) protected supply.
Use of an RCD
reduces the risk of electric shock.