Parker PSD1-SW1200 Скачать руководство пользователя страница 41

Страница: 41 / 109

192-011006N8 PSD1 Installation Guide

192-011006N8 2019-07

09.10.19 09:27

41 (109)

5.1

Before commissioning the drive, please observe the following:

CAUTION: Risk of electric shock

Caution - Risk of electric shock!

Before wiring or loosening electrical connections please observe the

following:

•

Risk of electric shock, disconnect power before removing cover resp.

disconnect the devices from the mains supply.

•

Caution!

Dangerous electrical voltage even after turning off the intermediate

capacitors:

Up to

3 minutes with PSD1-S and 10 minutes with PSD1-M

after switching off

mains supply, dangerous voltages may still be present.

Please check that no voltages are present (<50 V) at the output terminals DC+

and DC- of PSD1-S: X63/3 & X63/5 and with PSD1-M: Bus HV DC - 3 & 5. rail.

Only qualified electrician may commission the drive.

Accident prevention measures must be observed.

Please make sure that no small parts (screws, cable remnants, ..) enter the

devices.

Feedback system can be destroyed if configured incorrectly!

If you connect a PSD that has already been configured for a specific feedback

system to another feedback system, it can be destroyed by too high a voltage.

Procedure when changing the feedback system.

5.2

Mounting and dimensions

Ventilation:

•

During operation, the device radiates heat (heat dissipation). Please provide for

a sufficient mounting distance below and above the device (at least 100 mm) in

order to ensure free circulation of the cooling air.

•

Please do also respect the recommended distances of other devices.

•

Make sure that the mounting plate is not exhibited to other temperature

influences than that of the devices mounted on this very plate.

•

The devices must be mounted vertically on a level surface. Make sure that all

devices are sufficiently fixed.

Содержание PSD1-SW1200














































































































Результаты поиска

Содержание PSD1-SW1200

Отзывы:

Бренды по названию

Популярные бренды

Parker PSD1-SW1200, Руководство по установке

Результаты поиска

Содержание PSD1-SW1200

Отзывы:

Бренды по названию

Популярные бренды