Parker PSD1-SW1200 Скачать руководство пользователя страница 19

Страница: 19 / 109

192-011006N8 PSD1 Installation Guide

192-011006N8 2019-07

09.10.19 09:27

19 (109)

Data of the integrated dynamic brake module PSD1-M_P

Category

Specifications

Mains module

Maximum current

Max. Duty Cycle

Minimum resistance

value

Peak

Duration

PSD1-M_P010

28.8 A

4.27 A (500 W)

2.2 % (@60 s)

Ω

7.5 A (1500 W)

6.7 % (@60 s)

PSD1-M_P020

78.0 A

7.06 A (500 W)

0.82 % (@60 s)

Ω

22.3 A (5000 W)

8.2 % (@60 s)

•

Suitable for use on a circuit capable of delivering not more than 5000 rms

Symmetrical Amperes, 480 V ac +10 % maximum, when protected by Listed

♦

DIVQ Circuit Breakers manufactured by ABB, Stotz-Kontakt GmbH, Mod. No. S203UP-K

/ 480 Vac, 25 A for PSD1-M_P010

♦

R/C (JFHR2/8) Semiconductor Fuse type manufactured by Cooper Bussmann LLC,

Mod. No. 170M1366 oder 170M1566D, 690 VAC, 80 A, 200 kA RMS Sym for

PSD1-M_P020..

•

Power supply units PSD1-M_P need a fusing on the main site (branch circuit

protection) as stated below.

PSD1-M_P010

Maximum fuse rating per
device

Measure for line and device protection:
UL listing (DIVQ) fuses
Manufacturer: ABB, Stotz-Kontakt GmbH (E212323)
Model No.: S203UP-K, 1 fuse
480 VAC, 3-phase, 25 A, operating temperature 55 °C

PSD1-M_P020

Maximum fuse rating per
device
2 special purpose fuses in
line are required

Cable protection measure:

MCB (K characteristic) with a rating of 50A / 4xxVAC (depending on the input voltage)
Recommendation: (ABB) S203U-K50 (440VAC)

Device protection measure:

Circuit breakers 80A / 700VAC per supply leg in accordance with UL category JFHR2
Requirement: Bussmann 170M1366 or 170M1566D

Tightening torque of the wiring terminals

Risk of Electric Shock, wait at least 10 minutes before removing cover.

The field wiring terminals should be tightened with the torques mentioned below.

Only the supplied mating connectors must be used.

PSD1-M

2 A ... 15 A

X45 Motor

up to AWG10

up to 4 mm

Tightening torque

0.8 Nm

7 Lb.in



X46 motor brake

up to AWG14

up to 1.5 mm

Tightening torque

0.22 ... 0.25 Nm

1.95 ... 2.21 Lb.in

PSD1M_1800

2 A ... 30 A

X43 Motor

up to AWG20-8

up to 6 mm

Tightening torque

1.1 ... 1.7 Nm
11 ... 15 Lb.in



X44 motor brake

up to AWG30-14

up to 1.5 mm

Содержание PSD1-SW1200














































































































Результаты поиска

Содержание PSD1-SW1200

Отзывы:

Бренды по названию

Популярные бренды

Parker PSD1-SW1200, Руководство по установке

Результаты поиска

Содержание PSD1-SW1200

Отзывы:

Бренды по названию

Популярные бренды