background image

 

Chapter 2, ACRCOMM Module Hardware Set-Up 

 

 

25

ACRCOMM SERIAL COMMUNICATIONS 

 
The ACR2000 serial communication interface is software configurable.  At power-up, the 
default COM1/COM2 communications mode is RS-232.  
 

ACR2000/SA Boards: 

 
For Standalone ACR2000 boards, reconfiguration of the communications ports to RS-422 
must be performed via an RS-232 port.   
 
If one of the serial ports is a dedicated RS-232 port, reconfiguration of the second port 
may be accomplished at power-up (or at any time).  
 
If both ports are to be configured to RS-422 mode, the following must be performed:  
 

1. 

Open serial communication to one of the ports via RS-232.  

2. 

Load a PBOOT program containing the desired communication flags 
configuration for COM1 and COM2 ports.  

 
This will configure the serial ports to the desired mode of operation at power-up.  If a 
different communication mode is then required, disabling the User-Memory battery-
backup batteries via jumpers or a issuing a BRESET command (or issuing a FLASH 
ERASE command, if the programs are stored in flash memory) will set the 
communications modes back to default (RS-232) at the next power-up sequence.  
 

ACR2000/PS Boards: 

 
For PC ACR2000 boards with the communications option, the serial ports may be 
configured as above via a serial port, or at power-up (or any time) via the ISA bus 
communications port.   
 

Содержание ACR2000






















































Отзывы: