Parker ACR2000 Скачать руководство пользователя страница 47

Страница: 47 / 53

Chapter 3, ACR2000 Specification

ACR2000 SPECIFICATION, continued

ITEM SPECIFICATION

Feedback Types:

Any Differential 5VDC or 12VDC including:

- Quadrature Encoder
- Glass Scales
- Analog (Optional)

Watchdog Relay:

+24VDC @ 1.0 A
Single Pole - Double Throw (SPDT)
Hardwire through P2 analog header

External I/O Power Supply
Requirements:

+24 VDC (+3/-6VDC) @ 2A

Digital Inputs:

16 Optically Isolated (standard) @ External Voltage Supplied
Sinking or Sourcing Available
Activates on 10mA per input

Digital Outputs:

16 Optically Isolated (standard) @ External Voltage Supplied

Output Loads:
16 Outputs @ 50 mA continuously, each
or
Up to 6 Outputs @ 125mA continuously, each, distributed across the
two (2) output drivers, as follows:

up to 3 between OUT32 and OUT39

up to 3 between OUT40 and OUT47

Open Collector Sinking or Sourcing Type Available

A/D Inputs (On-Board Option):

Up to 8 single-ended or up to 4 differential
12 bit resolution
Configurable for various analog inputs
9 microsecond conversion time

Communications: PC-Bus

standard

COM1, COM2, and LPT available on optional ACRCOMM module
Simultaneous communications on all 4 ports

Serial Communications:
(ACRCOMM Module)

2 ports standard (COM1, COM2)
Software Configurable RS-232 or RS-422
Automatic Baud Detect (300 Hz - 38.4 KHz)

Содержание ACR2000






















































Результаты поиска

Содержание ACR2000

Отзывы:

Похожие инструкции для ACR2000

Бренды по названию

Популярные бренды

Parker ACR2000, Руководство по оборудованию

Результаты поиска

Содержание ACR2000

Отзывы:

Похожие инструкции для ACR2000

Бренды по названию

Популярные бренды