Parker ACR2000 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 53

background image

ACR2000 Hardware Manual

P/N PM08117

14

ACR2000 MOTHERBOARD JUMPERS

Battery Back-Up Select Jumpers (J10 and J11)

These two jumpers allow for disabling and enabling of the battery back-up when a
ACRCOMM communications module is present.

When an ACRCOMM module is present and the jumpers are set to “Battery Function
Enabled”, user programs on the board are retained when power is removed. When an
ACRCOMM module is present and the jumpers are set to “Battery Function Disabled”,
user programs on the board are not retained when power is removed.

When no ACRCOMM module is present, the jumpers must be set to “Battery Function
Disabled” position for ACR2000 to function.

Battery Back-up Jumpers

Battery Function

J10

J11

Battery Function Disabled

1-2

1-2

Battery Function Enabled

2-3

2-3

Table 1.7 ACR2000 Battery Back-Up Enable Jumpers

Refer to Figure 1 for jumper location.

«
...
22
23
24
25
26
...
»

Содержание ACR2000






















































Отзывы:

Нет отзывов

Похожие инструкции для ACR2000

Бренд: Laird Страницы: 36

Бренд: Ebyte Страницы: 14

Бренд: VMIC Страницы: 126

Бренд: Lanner Страницы: 109

MegaRAID SCSI 320-2X

Бренд: LSI Страницы: 4

Бренд: WHOOP Страницы: 26

Бренд: H3C Страницы: 3

Бренд: Z Microsystems Страницы: 51

Бренд: ICP DAS USA Страницы: 31

Tamar FCSAS102800

Бренд: Bridgeworks Страницы: 56

ibaBM-FOX-i-3o-D

Бренд: IBA Страницы: 13

Бренд: Intel Страницы: 469

X-NUCLEO-AMICAM1

Бренд: ST Страницы: 18

Бренд: LinMot Страницы: 62

StudioStation 100

Бренд: Extron electronics Страницы: 4

Бренд: Nedap Страницы: 3

Magellan Systems

Бренд: Paradox Страницы: 40

Бренд: IntraServer Technology Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды