Parker ACR2000 Скачать руководство пользователя страница 4

Страница: 4 / 53

CHANGE NOTICE, continued

ACR2000 Hardware Manual P/N PM08117 Version Change:

From: Version 1.05, Dated 5/20/1998

To:

Version 1.06, Dated 7/8/1999

1. ACR2000 Motherboard Jumpers –

Digital Input Reference Select Jumper
(J5)

R5VDC reference.

2. ACR2000 Motherboard Jumpers –

Digital Output Sink/Source Select
Jumpers
(J7 and J8)

R5VDC reference. Added jumper warning.

3. ACR2000 Motherboard Hardware

Wiring

R5VDC reference.

4. ACR2000 Motherboard Hardware

Wiring, Digital I/O Power (PWR1)

R5VDC reference.

5. Chapter 3 Overview

R5VDC reference.

6. ACRIO Module Jumpers – Digital

Input Reference Select Jumpers (J3 and
J4)

R5VDC reference.

7. ACRIO Module Jumpers – Digital

Output Sink/Source Select Jumpers
(J5 and J6)

R5VDC reference. Added jumper warning.

8. ACRIO Module Hardware Wiring,

Digital I/O Power (PWR1)

R5VDC reference.

Содержание ACR2000






















































Результаты поиска

Содержание ACR2000

Отзывы:

Похожие инструкции для ACR2000

Бренды по названию

Популярные бренды

Parker ACR2000, Руководство по оборудованию

Результаты поиска

Содержание ACR2000

Отзывы:

Похожие инструкции для ACR2000

Бренды по названию

Популярные бренды