Parker ACR Series Скачать руководство пользователя

Страница: 59 / 176

Parker

Hannifin

•

ROTARY

(Set Rotary Axis Length)—sets a rotary axis length used

in a shortest-distance calculation. The resulting move is never

longer than half the rotary axis length.

•

TMOV

(Time Based Move)—sets the time (in seconds) in which

the move is completed. The controller calculates a new master
motion profile to complete the move in the specified time. The

new motion profile values for acceleration, deceleration, stop

ramps, and velocity are no greater than the user-specified
values.

•

VECDEF

(Define Automatic Vector)—controls how the

Coordinated Moves Profiler calculates the master move

vector. The

VECDEF

command defines the weight each axis

receives in the vector calculation. The default value is 1 for
every axis.
In some applications, it is not desirable to include an axis in the

motion profile calculation. Suppose there is an application with
coordinated motion for axes X, Y, and Z, and rotary axis A.

Setting the axis A value to zero removes it from the vector
calculation. Axis A makes its move within the defined motion

profile, but is not part of the calculation itself.

•

VECTOR

(Set Manual Vector)—sets an independent vector

value for an axis removed from the motion profile calculation

through the

VECDEF

command. Because the axis is no longer

part of the motion profile calculation, it has no master velocity

with which it can make independent moves. The

VECTOR

command provides that value so the axis can make
independent moves.

Feedback Control Commands

The feedback control commands affect the velocity profiles and
define the encoder feedback used by axes in the current program.

Values must be set for each axis.

•

MULT

(Set Encoder Multipliers)—sets the count direction and

the hardware multiplication for the encoder of a given axis.
This command affects tuning gains, directions, distances,

velocities, and accelerations.

Caution —

Damage to equipment and/or serious

injury to personnel may result if

MULT

is changed

to a value inappropriate to the application.
Carefully consider the effects throughout the
application before applying a new value, and

perform a test without the load or mechanics

attached.

Making Motion 59

Содержание ACR Series

















































































































































































Результаты поиска

Содержание ACR Series

Отзывы:

Похожие инструкции для ACR Series

Бренды по названию

Популярные бренды

Parker ACR Series, Руководство программиста

Результаты поиска

Содержание ACR Series

Отзывы:

Похожие инструкции для ACR Series

Бренды по названию

Популярные бренды