Paradyne Hotwire 8303 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 138

Paradyne Hotwire 8303 Скачать руководство пользователя страница 55

3. DSL Card Configuration

8000-A2-GB26-70

April 2002

3-19

DSL Configuration Users Screens

Use the system information submenu of the Users screens to configure login
accounts for Telnet sessions directly to the DSL cards.

This menu item is not currently supported.

DSL Configuration Bridge Screens

Use the system information submenu of the Bridge screens to configure bridging
information such as aging timeout for MAC (Media Access Control) entries, and
VNID tagging.

Procedure

1. Follow this menu selection sequence:

Configuration

→

Bridge

(A-E)

2. The Bridge menu appears. Enter the desired value on each selected screen

and field as shown in

Table 3-4, Bridge Options

, and press Enter.

Once a valid

entry is saved, entries take effect immediately without requiring a card reset,
except for General (A-E-A). You must do card reset for General option
changes to take effect.

«
...
53
54
55
56
57
...
»

Содержание Hotwire 8303











































































































































Отзывы:

Нет отзывов