Paradyne Hotwire 8303 Скачать руководство пользователя страница 122

Страница: 122 / 138

B. Traps

B-2

April

2002

8000-A2-GB26-70

xDSL link up or
down

Transitions
threshold
exceeded

minor

Number of link down events
above threshold. This rate is
limited to once every
15 minutes.

1 hot_xdsl.mib

(Hotwire XDSL
interface)

xDSL margin
low

minor

Margin estimate below
customer set threshold.

3 hot_xdsl.mib

(Hotwire XDSL
interface)

xDSL margin
normal

normal

Margin estimate now above
customer set threshold.

103 hot_xdsl.mib

(Hotwire XDSL
interface)

xDSL port
failure

major

Processor detected bad DSL
modem chip set.

5 hot_xdsl.mib

(Hotwire XDSL
interface)

xDSL port
operational

normal

Processor now
communicating with DSL
modem.

105 hot_xdsl.mib

(Hotwire XDSL
interface)

xDSL port
speed low

warning

Port speeds decreased to
lower bound thresholds.

2 hot_xdsl.mib

(Hotwire XDSL
interface)

xDSL port
speed normal

normal

Port speed now above lower
bound threshold.

102 hot_xdsl.mib

(Hotwire XDSL
interface)

xDSL port
speed normal

normal

Port speed now above lower
bound threshold.

102 hot_xdsl.mib

(Hotwire XDSL
interface)

xDSL SN
selftest fail

warning

Selftest failure from an
Service Node.

19 hot_xdsl.mib

(Hotwire XDSL
interface)

xDSL test start

normal

Test started by any means.

6 hot_xdsl.mib

(Hotwire XDSL
interface)

xDSL test clear

normal

Test over.

106 hot_xdsl.mib

(Hotwire XDSL
interface)

Dynamic filter
injection failure

warning

Cannot inject or delete
dynamic filters to Service
Node on port

10 hot_dhcp.mib

(Hotwire DHCP
Relay Agent)

Ethernet link
down

major

—

2 MIB II

(RFC 1213)

Ethernet link up

normal

—

3 MIB II

(RFC 1213)

Table B-1.

DSL Card Traps (2 of 3)

Event

Severity

Comment

Trap #

MIB

Содержание Hotwire 8303











































































































































Результаты поиска

Содержание Hotwire 8303

Отзывы:

Paradyne Hotwire 8303, Руководство пользователя, Страница: 122 / 138

Результаты поиска

Содержание Hotwire 8303

Отзывы: