background image

1. Hotwire DSL System Description

1-4

  

April 

2002

8000-A2-GB26-70

DSL Cards

DSL cards is a generic term used in this document for a variety of types of line 
cards. 

DSL line cards with an Ethernet uplink consist of the following:

„

8303 24-port Integrated Services Digital Network Digital Subscriber Line 
(IDSL) cards. 

„

8310 4-port Multiple Virtual Lines (MVL) cards.

„

8510 4-port Rate Adaptive Digital Subscriber Line (RADSL) cards.

„

8312 12-port ReachDSL version 1 (formerly MVL) cards. 

„

8312 12-port ReachDSL version 2 cards. 

„

8343 24-port Symmetric Digital Subscriber Line (SDSL) cards.

„

8373 12-port RADSL cards. 

DSL line cards with an ATM uplink consist of the following:

„

8304 24-port IDSL cards. 

„

8314 12-port ReachDSL v1 (formerly MVL) cards. 

„

8314 12-port ReachDSL v2 cards. 

„

8344 24-port SDSL cards. 

„

8374 12-port RADSL cards. 

In addition, the following cards are also supported in the Hotwire chassis:

„

8335/8365/8385 ATM Line cards.

„

Time Division Multiplexer Symmetric Digital Subscriber Line (TDM SDSL) 
cards.

Содержание Hotwire 8303











































































































































Отзывы: