Paradyne Hotwire 8303 Скачать руководство пользователя страница 20

Страница: 20 / 138

1. Hotwire DSL System Description

1-10

April

2002

8000-A2-GB26-70

Troubleshooting and Diagnostics

The Hotwire DSL system provides DSL diagnostic menu options, for example,
that:

Display self-test results for CPU health, memory and ports, and reset time.

Show major alarms such as Selftest Failure, Processor Failure, and DSL or
Ethernet port failure.

Show minor alarms such as Configuration Error or Incorrect SN ports.

Run a nondisruptive packet echo test over the DSL line.

NOTE:

You must have Administrator permission to perform most of the
troubleshooting and diagnostic activities. However, you can run nondisruptive
tests as a user with Operator permission.

For more information about troubleshooting and diagnostics, see

Chapter 5,

Diagnostics and Troubleshooting

NOTE:

If you would like more information on DSL-based services, applications, and
network deployment, refer to Paradyne’s

The DSL Sourcebook.

The book may

be downloaded or ordered through Paradyne’s World Wide Web site at
www.paradyne.com.

Содержание Hotwire 8303











































































































































Результаты поиска

Содержание Hotwire 8303

Отзывы:

Paradyne Hotwire 8303, Руководство пользователя, Страница: 20 / 138

Результаты поиска

Содержание Hotwire 8303

Отзывы: