Paradyne Hotwire 8303 Скачать руководство пользователя страница 129

Страница: 129 / 138

C. Hotwire 6350 ReachDSL Modem

8000-A2-GB26-70

April 2002

C-5

Increasing the Number of End-User Systems

A single end-user system is attached to the Hotwire 6350 ReachDSL Modem by
using an Ethernet crossover cable. To increase the number of end-user systems,
connect all the PCs to an Ethernet hub using a straight-through cable.

The Hotwire ReachDSL port card supports 32 hosts/subnets per DSL port and the
Hotwire ReachDSL Modem supports up to 256 MAC entries.

Cables & Connectors

Standard twisted-pair CAT3 or better cables are recommended.

The LINE and PHONE interface connectors
use 6-pin, non-keyed modular plugs. RJ11 or
RJ14 6-pin connectors can be used.

Line & Phone Connectors

The LINE and PHONE jack pinouts are either filtered or unfiltered for POTS.

Pin #

Function

Not used

Ring 2 (optional)

DSL Ring 1

DSL Tip 1

Tip 2 (optional)

Not used

PHONE Jack Pinouts

LINE Jack Pinouts

Pin # 3, 4

Filtered for POTS

Pin # 3, 4

DSL and POTS

Pin # 2, 5

2nd POTS unfiltered

Pin # 2, 5

2nd line pass-through

98-15304a

6-Pin

RJ11 Plugs

Pin #1

Pin #6

Содержание Hotwire 8303











































































































































Результаты поиска

Содержание Hotwire 8303

Отзывы:

Похожие инструкции для Hotwire 8303

Бренды по названию

Популярные бренды

Paradyne Hotwire 8303, Руководство пользователя

Результаты поиска

Содержание Hotwire 8303

Отзывы:

Похожие инструкции для Hotwire 8303

Бренды по названию

Популярные бренды