Paradyne FrameSaver 9620 Скачать руководство пользователя страница 58

Страница: 58 / 79

Maintenance and Troubleshooting

5-4

9621-A2-GB20-30

August 1997

DTE Port 1 or 2

Label

Indication

Color

What It Means

P1/ P2

Port 1/ Port 2

Green

ON –

Port 1 is being monitored.

OFF –

Port 2 is being monitored.

TXD

Transmitted
Data

Green

ON –

Data sent from the DTE over
interchange circuit BA (ITU 103) is
all 1’s.

OFF –

Data sent from the DTE over
interchange circuit BA (ITU 103) is
all 0’s.

Blinking ON and OFF ( Rate: 5 Hz ) –

Both 1’s and 0’s are being received
from

the DTE; circuit state has

changed at least once during the
sampling interval.

RXD

Received Data

Green

ON –

Data received by the DTE over
interchange circuit BB (ITU 104) is
all 1’s.

OFF –

Data received by the DTE over
interchange circuit BB (ITU 104) is
all 0’s.

Blinking ON and OFF ( Rate: 5 Hz ) –

Both 1’s and 0’s are being received
from the DTE; circuit state has
changed at least once during the
sampling interval.

DTR

DTE or Data
Terminal Ready

Green

ON –

DTE is sending a control signal over
interchange circuit CD (ITU 108) to
indicate it is ready to transmit data.

OFF –

DTE has stopped sending the control
signal over interchange circuit CD
(ITU 108).

CTS

Clear to Send

Green

ON –

DCE is sending a control signal over
interchange circuit CB (ITU 106) to
indicate it is ready to transmit or
receive data.

OFF –

DCE has stopped sending the control
signal over interchange circuit CB
(ITU 106).

Содержание FrameSaver 9620
















































































Результаты поиска

Содержание FrameSaver 9620

Отзывы:

Похожие инструкции для FrameSaver 9620

Бренды по названию

Популярные бренды

Paradyne FrameSaver 9620, Руководство пользователя

Результаты поиска

Содержание FrameSaver 9620

Отзывы:

Похожие инструкции для FrameSaver 9620

Бренды по названию

Популярные бренды