Paradyne FrameSaver 9620 Скачать руководство пользователя страница 73

Страница: 73 / 79

Maintenance and Troubleshooting

5-19

9621-A2-GB20-30

August 1997

Message

What To Do

What It Indicates

Cause
No.

Suspended call
exists, but not call id

A call resume has been
attempted, but no
suspended call exists for
this phone number.

1. Verify the number in the

Calling ID # field for the
suspended call.

2. Reissue the Call

Resume command
using the correct
number.

Temporary failure

Network is not functioning
correctly, but the condition
is not expected to continue
for long.

Wait and try again.

Unallocated number

Destination requested
cannot be reached because
the Calling ID number is not
assigned or allocated.

Assign the Calling ID.
(Path: main/control/
isdn_call_profile)

User access
information
discarded

Network was unable to
deliver the access
information when trying to
establish the call.

No action needed.

User alerting, no
answer

During call establishment,
an alerting was received
but a connection was not.

1. Verify that the remote

device is operational
and configured to
answer. (Path: main/
configuration/edit/dbm/
physical)

2. Retry the call.

User busy

Called number cannot
receive the call.

Wait and try again.

Содержание FrameSaver 9620
















































































Результаты поиска

Содержание FrameSaver 9620

Отзывы:

Похожие инструкции для FrameSaver 9620

Бренды по названию

Популярные бренды

Paradyne FrameSaver 9620, Руководство пользователя

Результаты поиска

Содержание FrameSaver 9620

Отзывы:

Похожие инструкции для FrameSaver 9620

Бренды по названию

Популярные бренды