Paradyne FrameSaver 9620 Скачать руководство пользователя страница 45

Страница: 45 / 79

Displaying System Information

4-20

9621-A2-GB20-30

August 1997

What Statistics Are Collected?

Performance statistics are collected for the:

Physical interfaces

Frame relay link

Frame relay DLCI PVC connections

Compressed DLCIs

The following sets of statistics appear, based upon the interface selected:

Select . . .

For the . . .

Network Physical

Network interface’s physical performance statistics.

Network Frame Relay

Network interface’s frame relay performance statistics.

Port-1 or 2 Physical

Port physical interface’s performance statistics.

Port-1 or 2 Frame Relay

Port’s frame relay performance statistics.

DBM Physical

ISDN BRI DBM’s physical interface performance
statistics.

BRI-B1 Physical

DBM’s BRI physical performance statistics for
B channel 1.

BRI-B1 Frame Relay

DBM’s BRI frame relay performance statistics for
B channel 1.

Clear Statistics

Screen that allows performance statistics to be cleared
(reset to 0). You can clear these statistics for the
individual interfaces, or for all interfaces.

Statistics can also be cleared from the individual
performance statistics screens.

Selection only appears when:

Port is enabled.

Interface (the port, or BRI-B1) is enabled and the frame relay Link Status is enabled.

ISDN BRI DBM is installed.

Содержание FrameSaver 9620
















































































Результаты поиска

Содержание FrameSaver 9620

Отзывы:

Похожие инструкции для FrameSaver 9620

Бренды по названию

Популярные бренды

Paradyne FrameSaver 9620, Руководство пользователя

Результаты поиска

Содержание FrameSaver 9620

Отзывы:

Похожие инструкции для FrameSaver 9620

Бренды по названию

Популярные бренды