Paradyne COMSPHERE 3610 Скачать руководство пользователя | Manualshive

Страница: 132 / 238

background image

COMSPHERE 3600 Series Data Service Units

5-18

July 1999

3610-A2-GB41-70

While the DSU is in Local Loopback, any data

transmission by the DTE is returned as received data. An
operator can send a test pattern and verify correct
reception of the test. The DSU does not monitor this
testing.

When Local Loopback is requested of an inactive core,

there is no effect since data from DTE ports is routed
through the active core.

For TDM, MCMP, or Bridge mode, the entire data

stream is looped back; therefore, all six ports are in Local
Loopback. Use the DTE Loopback command to loop back
only one port. Command Complete appears at the
loopback conclusion.

NOTE

When Nondisruptive Diagnostics is
enabled (Diag Type: NonD), Local
Loopback disrupts secondary
channel transport communications.
For a control DSU, the DSU may
report No Response or Tributary
Time-out during the test.

To access Local Loopback from the top-level menu,

make the following selections:

•

Local (F1)

•

Test

•

DSU

•

Lpbk

•

LL

Local Loopback can also be initiated by the DTE

attached to Port 1 by raising Pin 18 of the EIA-232-D/
V.24 interface or Pin L of the V.35 interface, provided the
Local Loopback by DTE configuration option is enabled.

Results

Data transmitted to the DSU is returned to the DTE.

F1

DSU Local Lpbk:
Command Complete

F2

F3

NOTE

During Local Loopback, the DSU
uses internal timing. This may be a
problem for extended circuit
applications. In this case, execute
a DTE Loopback instead of a
Local Loopback.

«
...
130
131
132
133
134
...
»

Содержание COMSPHERE 3610















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

Бренд: NEC Страницы: 72

Бренд: TDC Страницы: 27

ELECTRA ELITE IPK II

Бренд: NEC Страницы: 617

VERSA DOCK - SERVICE

Бренд: NEC Страницы: 8

Бренд: National Instruments Страницы: 17

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 23

Бренд: NavigateWorx Страницы: 71

Бренд: X-Micro Страницы: 74

Бренд: Watchguard Страницы: 40

StorageWorks AIT 35GB AutoLoader

Бренд: Compaq Страницы: 4

Бренд: Renesas Страницы: 20

Бренд: H3C Страницы: 3

Бренд: Xyclop Страницы: 144

Бренд: Silvertel Страницы: 9

Бренд: TP-Link Страницы: 2

Бренд: Acromag Страницы: 23

Бренд: Top Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды