background image

DGP2-640 Icon LCD Keypad  

11

4.10 Confidential Mode Timer

Section 

[012]

: Default = 120 seconds 

Section

 [012]

 determines the amount of time a keypad is inactive 

before the keypad enters Confidential Mode. For more information, 
refer to 

Confidential Mode

 on page 8. The Confidential Mode timer 

can be set from 005 seconds to 255 seconds. 

5.0 Programmable Output Options

5.1 PGM State

Section 

[011]

: Option 

[1]

The keypad's on-board PGM can be set as normally open or 
normally closed. When an open PGM is activated, it will close the 
circuit to the ground and enable any devices connected to it. When a 
closed PGM is activated, it will open the circuit and disable any 
devices connected to it. When the PGM Activation Event occurs (see 

PGM Activation

 on page 12), the PGM will switch to its opposite state 

(i.e. open to closed or closed to open). The PGM is limited to 50mA.

Option 

[1] 

OFF = PGM is Normally Open (default)

Option

 [1]

 ON = PGM is Normally Closed

5.2 PGM Deactivation Mode

Section 

[011]

: Option 

[2]

If option 

[2]

 is enabled, the keypad's on-board PGM will be 

deactivated according to the PGM Timer

 

(see 

PGM Timer

 on page 

12) instead of the PGM Deactivation Event.

Option 

[2] 

OFF = Deactivation follows PGM Deactivation Event (default)

Option 

[2] 

ON = PGM will deactivate according to the PGM Timer

DGP2640_EI00.fm  Page 11  Thursday, April 7, 2005  12:05 PM

Содержание Digiplex EVO DGP2-640

























Отзывы: