35
34
USER MANUAL
PANDORA DXL 1840L CAR SERVICE-SECURITY SYSTEM
Level 8 – Recording Bluetooth GPS/GLONASS receiver (NAV-035 BT)
To record a Bluetooth GPS/GLONASS receiver, enter programming mode and press VALET button 8
times. The LED indicator will light green and the system will enter the recording of a receiver. Connect
the receiver in accordance with its installation manual. The system will confirm the registration with a
short sound signal and red light of LED indicator.
Saving changes:
To finish the recording of the engine compartment module, press VALET button once, the series of
red and green flashes of the status LED will confirm the saving, switch on the ignition to save the set-
tings and exit programming mode.
Level 10 – Configuring system settings via the wireless interface
This function is under construction.
Level 11 – Programming and configuring ‘Immobilizer PIN code’
To program the «Immobilizer PIN code», enter the programming mode and press VALET button 11
times. The level is divided into 3 sublevels (Sublevel 11.1 – Selecting buttons; sublevel 11.2 entering
PIN-code; sublevel 11.3 – confirmation of the PIN-code input).
The system will automatically enter the sublevel 11.1 (Selecting buttons) after entering the level 11.
The system can determine buttons via analog “Code immobilizer” input or via digital protocol of a car.
It is necessary to configure an analog input (INP) as ‘Code immobilizer’ in the settings of the base
unit inputs when implementing the “Code immobilizer” via an analog input. It may be necessary to
switch on the ignition after entering the level 11 of programming (if the car bus is active only when
the ignition is switched on) when implementing the “Code immobilizer” via digital car bus protocol.
After selecting active buttons enter the sublevel 11.2 (Entering PIN-code) by pressing VALET but-
ton once. Program PIN-code using selected buttons at this sublevel; press VALET button once and enter
PIN-code again. To confirm PIN-code re-entering and save all the settings press VALET button once
again.
Sublevel 11.1 - Selecting buttons:
This sublevel is used to select active buttons via digital protocol of a car or via ‘Code Immobilizer’
analog input. To determine the activity of the analog “Code Immobilizer” input, apply potential to the
corresponding input (INP) of the base unit, LED indicator will be flashing orange.
If you determine buttons via digital protocol select one or more buttons (up to four) for entering
the secret code of the immobilizer. To do this press the selected button, LED indicator will confirm input
with orange flashes. If there are no orange flashes when any button is pressed, then this button is not
recognized by the system, select a different button. Repeat the procedure to select the second, third,
fourth button and enter the next sublevel. To enter the next sublevel 11.2l press VALET button once.
Sublevel 11.2 - Entering PIN-code:
Program immobilizer deactivation PIN-code using selected button or buttons. Enter the first digit
by pressing the previously selected button (pauses between presses should not exceed 1 second). The
base unit will confirm entering with red flash of LED indicator. Enter the second (third, fourth) digit by
pressing the previously selected button. The base unit will confirm entering of each digit with red flash
of LED indicator.
Input the required number of digits (up to 4) and then press VALET button. The system will confirm
receiving of the secret validator code with long red flash of LED indicator and will wait for confirmation
of PIN-code.
Sublevel 11.3 - Confirmation of the PIN-code input:
11.2 Enter PIN-code again similarly to the procedure (level 11.2 – Entering PIN-code) and press
VALET button. The system will confirm correct PIN-code with red and green flashes of LED indicator and
will memorize PIN-code, and then the system will proceed to programming mode awaiting level input.
Incorrect confirmation is indicated with long red flash of LED indicator, after that the system will return
to programming mode.
Level 15 – Disabling/enabling immobilizer tag
To disabling/enabling of immobilizer tag, enter programming menu and press VALET button 15
times. LED indicator will light green (green light indicates enabled tag) and the system will wait for the
“Secret PIN-code” entering. Red light of LED indicates disabled immobilizer tag.
Disabling radio tag:
LED indicator will light green after entering the programming level. The system will wait for entering
the ‘Secret PIN-code’. Enter the ‘Secret PIN-code’ that is written on the owner’s plastic card. The system
will confirm disabling of the radio tag with two sound signals of the siren and a long red LED flash. After
that the system will return to the programming menu. If the PIN-code is not entered within 10 seconds
or the input is incorrect, a siren will sound one signal, LED will produce the series of red and green
flashes and the system will return to the programming menu.
Enabling radio tag:
LED indicator will light red after entering the programming level. The system will wait for action.
Press VALET button once to enable radio tag. The system will confirm enabling with one short sound
signal of a siren and a green LED light. After that the system will return to the programming menu.
