33
32
USER MANUAL
PANDORA DXL 1840L CAR SERVICE-SECURITY SYSTEM
Level 2 – Changing the factory preset of the service PIN-code
Prepare a new value of the ‘Service PIN-code’, it should consist of 4 digits (from 1 to 9).
Write down or remember the new PIN-code.
Enter programming menu and then press VALET button twice. The system will enter ‘Changing Ser-
vice PIN-code’ mode and the status LED indicator will turn off.
Changing the ‘Service PIN-code’:
• Enter the first digit of the code using VALET button. Press the button a number of times, equals
to the first digit. Pauses between presses should not exceed 1 second, every pressing will confirm with
orange LED indicator flash. Pause for more than 1 second and red LED indicator confirms the input of
the first digit. Then you can enter the next digit.
• Enter the other numbers in the same manner. The input of the fourth number will be confirmed
by series of red and green LED indicator flashes. The system will wait for PIN-code re-entering.
• Enter all four digits again;
• If you were able to correctly enter the ‘Service PIN-code’ twice, the indicator will produce the series
of red and green flashes, new PIN-code will be recorded, the system will return to programming mode.
In case of the incorrect code input the indicator will be lit red, the system will return to programming
mode.
Level 3 – Recording the idle speed to the system memory
To timely turn off the starter during automatic or remote engine start via digital or analog tachometer
input and the correct operation of the ‘Smart Turbo Timer’, it is necessary to record the engine idle speed
To record idle speed to the non-volatile system memory, enter the programming menu. Press VALET
button three times. Switch on the ignition and start the engine after entering this level of programming
(the engine should be warmed-up, idle speed should match the stable idle speed of the warmed-up en-
gine). The system will confirm the presence of the idle speed status with green flashes of LED indicator.
Wait until the stable idle speed will be reached and save the changes
Saving changes:
Press VALET button once to save idle speed. Successful recording of the idle speed will be confirmed
with the series of red and green flashes of LED indicator. The system will exit programming menu and
reboot after saving the idle speed.
Level 4 – Resetting to factory settings.
The procedure recovers the factory settings of the system without deleting previously registered de-
vices (tags, mobile device, relays, etc.) that is stored in the non-volatile memory.
To reset the settings enter the programming mode and press VALET button four times. Press and hold
VALET button for more than 4 seconds until siren sound, then release the button. The system will con-
firm the resetting to the factory settings with a long red flash of LED indicator. After that the system will
return to a programming mode
Level 5 – Recording Bluetooth engine compartment module
To record a Bluetooth engine compartment module, enter programming mode and press VALET button
5 times. The LED indicator will light green and the system will enter the recording of an engine com-
partment module mode. Connect the module in accordance with installation manual. The system will
confirm the registration with a short sound signal.
Saving changes:
To finish the recording of the engine compartment module, VALET button should be pressed once
again, the series of red and green flashes of the status LED will confirm the saving, switch on the ignition
to automatically save the settings and exit programming mode.
Levels 6, 7 – Recording Bluetooth radio relays
Radio relays recording is performed one by one starting from the 6 level: radio relay №1 is
recorded on the 6 level; radio relay №2 is recorded on the 7 level. The radio relay can be overwrit-
ten only on the level of its initial registration.
To record Bluetooth radio relays №1, №2, enter programming mode and press VALET button 6 times
for radio relay №1 or 7 times for radio relay №2. LED indicator will light green and the system will enter
the recording of a radio relay mode. Connect a relay in accordance with installation manual. The system
will confirm recording with a short sound signal.
Saving changes:
To finish the recording of the Bluetooth radio relay, VALET button should be pressed once again, the
series of red and green flashes of the status LED indicator will confirm the saving, switch on the ignition
to automatically save the settings and exit the programming mode.