background image

Precautions

Refer installation work to the dealer. 

Installation work requires technique and experiences. 
Failure to observe this may cause fire, electric shock, 
injury, or damage to the product. 
Be sure to consult the dealer. 

Stop the operation immediately when something is 
wrong with this product. 

When smoke goes up from the product, the smell of 
smoke comes from the product, or the exterior of the 
product has deteriorated, continued use will cause a fire 
or fall of the product resulting in injury, or damage to the 
product. 

Do not attempt to disassemble or modify this prod-
uct. 

Failure to observe this may cause fire or electric shock. 
Consult the dealer for the repair or inspections. 

Do not insert any foreign objects. 

This could permanently damage the product. 
Turn the power off immediately and contact qualified ser-
vice personnel for service. 

Select an installation area that can support the total 
weight. 

Selecting an inappropriate installation surface may cause 
the product to fall down or topple over, resulting in injury. 
Installation work shall be started after sufficient reinforce-
ment. 

Periodic inspections shall be conducted. 

Rust on the metal parts or screws may cause a fall of the 
product resulting in injury or accidents. 
Consult the dealer for the inspections. 

Do not use this product in an inflammable atmo-
sphere. 

Failure to observe this may cause an explosion resulting in 
injury. 

Avoid installing this bracket in the locations where 
salt damage occurs or corrosive gas is produced.

Otherwise, the mounting portions will deteriorate and acci-
dents such as a fall of this product may occur.

The measures of protection against a fall of this 
product shall be taken. 

Failure to observe this may cause a drop resulting in injury. 
Be sure to install the safety wire.
    

The exclusively designed mount bracket shall be 
used.

Failure to observe this may cause a drop resulting in injury 
or accidents.
Use the exclusively designed mount bracket for installa-
tion.

The screws and bolts must be tightened to the 
specified torque.

Failure to observe this may cause a drop resulting in injury 
or accidents.

Do not install this product in locations subject to 
vibration.

Loosening of mounting screws or bolts may cause a fall of 
the product resulting in injury.

Do not strike or give a strong shock to this product.

Failure to observe this may cause fire or injury.

Turn the power off when do wiring of this product.

Failure to observe this may cause electric shock. In addi-
tion, short circuit or wrong wiring may cause fire.

Do not rub the edges of metal parts with your hand. 

Failure to observe this may cause injury.

Keep SDHC/SD memory cards (option) away from 
infants and children.

Otherwise, they may swallow the cards by mistake.
In this case, consult a doctor immediately.

Do not touch this product, the power cable or the 
connected cables during thunder. 
(Including during installation work)

Failure to observe this may cause electric shock.

Install this product in a location high enough to 
avoid people and objects from bumping the product. 

Failure to observe this may cause injury. 

Do not hang down from this product or use this 
product as a pedestal. 

Failure to observe this may cause injury or accidents. 

Turn the power off when cleaning this product. 

Failure to observe this may cause injury.

9

Содержание WV-SC386





































Отзывы: