Manual Fine Adjustment for AWC (ATW)
You can set the white balance items manually.
1. To set MASK SET, proceed as described in steps 2 to 4 of “ALC mode with SUPER-D2
OFF and ELC mode”.
2. Move the cursor to R.
3. Press
L
or
M
to obtain the optimum amount of red gain.
4. Move the cursor to B.
5. Press
L
or
M
to obtain the optimum amount of blue gain.
Note:
When you need to set MASK SET, re-adjust to obtain the optimum amount of red and
blue gain.
8. Motion Detector Setting (MOTION DET)
The motion detector detects the moving objects in the scene by monitoring changes in
brightness level. You can select the level of sensitivity for motion detection.
When this camera is connected to a compatible intelligent CCTV system, the camera trans-
mits an alarm signal by multiplexing it with the video signal.
1. Move the cursor to MOTION DET and
select ON.
The factory default setting is OFF.
2. Press
I
. The MOTION DETECT
menu appears on the monitor screen.
3. Move the cursor to MASK SET and press
I
. MASK SET lets you set 48 mask areas.
To set MASK SET, proceed as described in steps 2 to 4 of “ALC mode with SUPER-D2
OFF and ELC mode”.
4. Move the cursor to ALARM and select ON or OFF to set the alarm for DISPLAY MODE.
Note:
When using the WV-RM70, WV-CU550 series, WV-CU161 or WV-CU360 controller
with this model, select OFF for ALARM.
5. Move the cursor to DISPLAY MODE and press
I
to see the current setting. The
masks that detect the brightness changes start blinking.
6. To raise detection sensitivity, press
I
to return to the MOTION DETECT menu.
7. To obtain the optimum detection level, move the “I” cursor to adjust the level.
8. Repeat the procedures above to obtain a satisfactory setting.
Notes:
• When the camera is not used in a Panasonic Intelligent CCTV System, select OFF.
Otherwise, video equipment may malfunction because of the alarm signal misinterpreta-
tion for a time code signal.
• The motion detector may malfunction when the lightning equipment continuously turns
on and off, or when ELC mode is selected for ALC/ELC.
• Set MASK SET over the areas where leaves or curtains etc. are swaying.
• Adjust the detection level on the menu to prevent misinterpretation under low light con-
ditions with noise.
• It takes about 0.2 seconds for the alarm signal to reach the VCR’s alarm terminal after
the camera detects the moving object.
• The motion detector is not specifically intended to prevent theft or fire.
9. Lens Drive Signal Selection (LENS DRIVE)
This item is used to select the type of auto iris lens drive signal to be supplied to the lens
from the auto iris lens connector.
1. Move the cursor to LENS DRIVE.
The factory default setting is DC.
2. Select DC if you are using the auto iris lens that requires a DC drive signal.
Select VIDEO if you are using the auto iris lens that requires a video drive signal.
10. Special Menu
This menu lets you adjust and set up the video signal of the camera to meet your require-
ments.
Move the cursor to END in the bottom
line of the CAM SET UP menu and
press
L
and
M
simultaneously
(holding down
L
and press
M
) for 2
seconds or more. The SPECIAL menu
appears on the monitor screen.
10-1. Camera Picture Upside Down Positioning (UP SIDE DOWN)
1. Move the cursor to UP SIDE DOWN.
2. Select ON when you want to turn the picture upside down.
10-2. Chroma Level Setting (CHROMA GAIN)
1. Move the cursor to CHROMA GAIN.
2. While observing the vectorscope or color video monitor, move the “I” cursor to adjust
the chroma level.
10-3. Aperture Gain Setting (AP GAIN)
1. Move the cursor to AP GAIN.
2. While observing the waveform monitor or color video monitor, move the “I” cursor to
adjust the aperture gain level.
10-4. Pedestal Level Setting (PEDESTAL)
1. Move the cursor to PEDESTAL.
2. While observing the waveform monitor or color video monitor, move the “I” cursor to
adjust the pedestal level (black level).
10-5. Chroma Phase (Hue) Setting (HUE)
1. Move the cursor to HUE.
2. While observing the vectorscope or color video monitor, move the “I” cursor to adjust
the hue (chroma phase) level.
10-6 BW
This function lets you automatically switch from color to black-and-white pictures in low light
conditions such as at night.
** MOTION DETECT **
LEVEL ....I....
- +
DISPLAY MODE
ALARM OFF
MASK SET
RET END
↵
↵
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER ---
AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
MOTION DET OFF
LENS DRIVE DC
END SET UP ENABLE
↵
↵
↵
** SPECIAL **
UP SIDE DOWN OFF
CHROMA GAIN ....I....
AP GAIN ....I....
PEDESTAL .I.......
HUE .I.......
- +
BW OFF
BURST(BW) ON
CAMERA RESET
/
PUSH SW
RET END
