22
Step 4
When attaching the front panel (operating section) while the
power is on, press the [ALARM RESET] button.
→
The indicators on the front panel (operating section) will
light or blink.
EXT STORAGE
MODE
DATA
RS485(CAMERA) 10/100BASE-T
ALARM
ALARM/CONTROL
VIDEO
OUT-CASCADE-IN
CASCADE IN
MONITOR
OUT
OUT MONITOR OUT(HD)
AUDIO IN
AUDIO
OUT
3
2
1
1 2 3 4 5 6 7 8
1
2
3
4
4
2
3
1
1
2
5
6
7
8
9
10
11
12
13
14
15
16
IN
OUT
2
1
3
4
5
6
7
7
1
2
1
2
8
9
10
11
12
13
14
15
16
POWER
AC IN
SIGNAL
GND
ON
OFF
OUT
IN
OUT
CASCADE
1
2
q
w
e r
t
y u
!2
!3
!4
!5
!6
!7 !8
!1
i
!0
o
q
Alarm/Control connector (D-sub 25-pin) [ALARM/
CONTROL]
Connect a control switch to control the recorder using
an external device such as a buzzer or a lamp.
(
☞
Page 44)
w
Alarm connector (D-sub 25-pin) [ALARM]
Connect an external device that outputs alarm signals
(such as a sensor, door switch, etc.) to this connector.
(
☞
Page 48)
e
External storage connector 1-3 [EXT STORAGE]
Connect the optional extension unit (WJ-HDE400/G) to
this connector using the dedicated connection cable
provided with the extension unit. (
☞
Page 33)
r
Mode switch [MODE]
Determine the operational mode of the recorder using
this switch. (
☞
Page 51)
t
DATA port [DATA]
Connect a PS·Data compatible device to this port.
(
☞
Page 35)
y
RS485 port [RS485/CAMERA]
Connect an RS485 combination camera to this port.
(
☞
Page 42)
u
Network port [10/100BASE-T]
Connect this recorder to a network (10BASE-T/
100BASE-TX) using this port. When the recorder is con-
nected to a network, it is possible to operate the record-
er from a PC via a network.
i
Audio cascade input (RCA pin jack) [CASCADE IN])
Use this connector for audio input from another recorder
when it is connected in cascading connection.
o
SIGNAL GND terminal
Connect this terminal to the SIGNAL GND terminals of
the devices in the system for signal ground. When oper-
ating the recorder and the devices in the system without
signal ground, oscillation or noise may be produced.
!0
Power button [POWER]
Press this button to turn on/off the power of the record-
er. When this button is pressed again, the operation is
finished and the power is turned off.
!1
Power inlet [AC IN]
Connect the provided power cord to this inlet. The
power plug is a 2-conductor plug with grounding termi-
nal type.
!2
Video input connector 1 to 16 (BNC)
[VIDEO IN 1 to 16]
Connect system cameras and combination cameras to
these connectors. When connecting combination cam-
eras, connect them to the video input connector 1-8
(coaxial communication compatible).
!3
Video output connector 1 to 16 (BNC, active loop
through) [VIDEO OUT 1 to 16]
Images input to the video out connectors 1-16 will be
output from these connectors. When the power is off,
images will not be output to the video output connector
1-16.
Note:
• After attaching the front panel (operating section) to the
recorder, make sure that the indicators on the front panel
(operating section) are lighting or blinking by pressing the
[ALARM RESET] button.
■
Rear view
