153
Specifications
• General
Power source:
220 V to 240 V AC, 50 Hz/60 Hz
Power consumption:
130 W
Ambient operating temperature:
+5 °C to +45 °C
Ambient operating humidity:
5 % to 90 % (non condensing)
When installing WJ-HDB611E: 10 % to 80 % (non condensing)
Maximum operating altitude:
2 000 m or less
Dimensions (excluding rubber
feet and projections)
430 mm (W) x 132 mm (H) x 400 mm (D)
Mass:
When no hard disk drive is installed: 14 k
g
When 4 hard disk drives are installed: 17 k
g
Finish:
Front panel: Solid metallic coating
Top cover: Solid metallic coating
Rear panel: Galvanized steel
• HDD (Locally procured - Contact your dealer about purchasing hard disk drives.)
Hard disk drive:
3.5 type hard disk drive (Up to 4 hard disk drives can be installed.)
• Input/output
Video
Video input connector:
1 V [p-p]/75 Ω, x16 (1ch to 16ch) (BNC)
Vertical timing pulse multiplexed, HD616K/G: x8 (1ch to 8ch), HD716K/G: x16
Cascade input connector:
1 V [p-p]/75 Ω (BNC)
HDMI, x2
Video output connector:
1 V [p-p]/75 Ω, active loop-thru output, x16 (1ch to 16ch) (BNC)*
1
Monitor output connector:
1 V [p-p]/75 Ω, x2 (BNC)
Monitor (HDMI) connector:
HDMI, x2*
8
Video output connector (front):
1 V [p-p]/75 Ω, x1 (RCA pin)
Audio
Audio input connector:
–10 dBV, 10 kΩ, unbalanced, x4 (RCA pin)
Cascade input connector:
–10 dBV, 10 kΩ, unbalanced x 1 (RCA pin)
Audio output connector:
–10 dBV, 600 Ω, unbalanced, x1 (RCA pin)
Audio output connector (front):
–10 dBV, 600 Ω, unbalanced, x1 (RCA pin)
Others
External storage connector:
x3
Mouse connection port:
x1
Alarm/control terminal:
8 to 16ch alarm output*
3
, alarm reset input*
2
, emergency recording input*
2
, available
disk space warning output*
3
, HDD error output*
3
, camera error output*
3
, error out-
put*
3
, outage processing end output*
4
, time adjustment input/output*
5
, sequence
switchover input/output*
5
, alarm suspension input*
2
, outage detection input*
2
, exter-
nal recording mode switching input*
2
, +5 V output*
6
(25-pin D-sub)
Alarm terminal:
1ch - 16ch alarm input*
2
, 1 - 7ch alarm output*
3
(25-pin D-sub)
RS485 port:
RS485 (full duplex/half duplex*
7
), x2 (RJ-11)
DATA port:
RS485, x2 (RJ-11)
Network port:
10BASE-T/100BASE-TX (RJ-45)
Maintenance port:
10BASE-T (RJ-45)
SDHC/SD memory card slot:
SDHC/SD memory cards applicable (miniSD cards and microSD cards not applica-
ble)
*1 When power is not supplied, the video output signal was not sent from the recorder even if a video input signal is supplied.
*2 Non-voltage make contact input, 50 kΩ +5 V DC pull-up
