Panasonic WH-SDC03E3E5 Series Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 127

background image

67

14. Servicing

Mode

14.1 How to Take Out Front Plate

Please follow the steps below for take out front plate. Before removing the front plate of indoor unit, always switch off
all power supply (i.e. indoor unit power supply, heater power supply and tank unit power supply).

1 Remove the 2 mounting screws which located at bottom of the front plate and 1 mounting screw at the front

of the plate.

2 Gently pull the lower section of the front plate towards you to remove the front plate from left and right hooks.
3 Hold the left edge and right edge of front plate to lift up front plate from hooks.

14.2 How to Take Out Side Cabinet

Please follow the steps below to remove the side
cabinet. Before removing the front plate of indoor unit
always switch off all power supply (i.e. indoor power
supply, heater power supply and tank unit power
supply).

1 Perform the steps in HOW TO TAKE OUT

FRONT PLATE.

2 Remove all the 13 mounting screws on the left,

right and top of the side cabinet.

3 Gently remove the side cabinet by holding both

of the handles.

14.3 Test

Run

1 Fill up the boiler tank with water. For details refer to boiler tanks installation instruction and operation

instruction.

2 Set ON to the indoor unit and RCCB. Then, for control panel’s operation please refers to air-to-water

heatpump’s operation instruction.

3 For normal operation, pressure gauge reading should be in between 0.05 MPa and 0.2 MPa.

If necessary, adjust the water pump speed accordingly to obtain normal water pressure operating range. If
adjust water pump speed cannot solve the problem, contact your local authorized dealer.

14.4 Proper Pump Down Procedure

Strictly follow the steps below for proper pump down procedure. Explosion may occur if the steps are not

followed as per sequence.
1 When the heatpump unit is not in operation(standby), press the “SERVICE” switch on control panel to enter

SERVICE mode. Operate the system in Sr : 01 mode for pump down operation.

2 After 10~15 minutes, (after 1 or 2 minutes in case very low ambient temperatures (< 10°C)), fully close 2 way

valve.

3  After 3 minutes, fully close 3 way valve.
4  Press the “OFF/ON” switch on control panel to stop pump down operation.
5  Remove the refrigerant piping.

«
...
65
66
67
68
69
...
»

Содержание WH-SDC03E3E5 Series
































































































































Отзывы:

Нет отзывов

Похожие инструкции для WH-SDC03E3E5 Series

Бренд: Wacker Neuson Страницы: 38

Бренд: Calpeda Страницы: 44

Бренд: Calpeda Страницы: 64

Бренд: Calpeda Страницы: 32

Бренд: WACKER Group Страницы: 60

VRV IV Q+ Series

Бренд: Daikin Страницы: 48

Бренд: Carrier Страницы: 30

Бренд: Edwards Страницы: 16

Бренд: York Страницы: 14

Бренд: Toyostove Страницы: 18

MENAI D E - MOUNTING

Бренд: RADSON Страницы: 4

Бренд: ARESA Страницы: 13

Бренд: Hyco Страницы: 12

DRENAG 1000-1200

Бренд: Saci Страницы: 134

Бренд: Trane Страницы: 8

Бренд: Lumme Страницы: 10

Бренд: Eaton Страницы: 21

Бренд: Dimplex Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды