Panasonic WH-SDC03E3E5 Series Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 127

background image

51

12.1.8 Setting Water Outlet Temperature for Heat Mode

The set temperature define the parameters for the outdoor ambient temperature dependent operation of the unit.

Where by the internal water setting temperature is determined automatically depending on the outdoor
temperature. The colder outdoor temperatures will result in warmer water and vice versa. The user has the
possibility to shift up or down the target water temperature by control panel setting.

Outdoor temperature is updated every 30 minutes when operation ON.

12.1.8.1 Heating

Mode

Operation Time Chart

Operation of heat pump provide heating capacity to room side by hot water through heating panel, floor or fan

coil.

1 3 ways valve control:

o

3 ways valve switch and fix to heating side.

2  Heat pump operate follow normal heating operation.
3  Backup heater operate follow normal operation.
4  Solar 3 way valve operates follow solar operation specification.
5  2 way valve opens.

12.1.9 Water Temperature Thermo Shift Setting

Switchs are ignored during “PUMPDW” = ON.

Switchs are ignored during “STATUS” = ON.

“

▲

”, “

▼

”, ”SELECT” switch are ignored if “SETTING” = OFF.

“CANCEL” switch is ignored if “SETTING” = OFF & “STATUS” = OFF.

If “SET” Switch pressed for less than 5secs, immediately enter water temperature shift setting mode.

Once enter this setting mode, “SETTING” display is ON.

This setting mode is used to easily shift the target water outlet temperature.

«
...
49
50
51
52
53
...
»

Содержание WH-SDC03E3E5 Series
































































































































Отзывы:

Нет отзывов

Похожие инструкции для WH-SDC03E3E5 Series

Бренд: Bacharach Страницы: 12

Бренд: SAER Elettropompe Страницы: 72

Бренд: JABSCO Страницы: 4

Бренд: ACESOL Страницы: 36

Бренд: Daikin Страницы: 60

ES38 RHFE-1004FTA

Бренд: Rinnai Страницы: 12

Бренд: SGS Страницы: 10

Бренд: Annovi Reverberi Страницы: 4

Бренд: MITSUWA Страницы: 20

SL MINITHERM DNLA

Бренд: Intertec Data Systems Страницы: 8

Бренд: Jaga Страницы: 11

Бренд: Electrorad Страницы: 16

Бренд: GORMAN-RUPP PUMPS Страницы: 25

Бренд: Intex Страницы: 5

Quick-Fill 58609

Бренд: Intex Страницы: 5

SILICIUM 3 IN 1

Бренд: CLIMASTAR Страницы: 16

Бренд: FLORABEST Страницы: 94

Бренд: Quincy Compressor Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды