Panasonic WH-MXF09D3E8 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 125

background image

61

2. Backup heater anti freeze control:

Backup heater turns ON when

ALL

the below conditions are fulfilled:

o

Water inlet/outlet temp. < 6°C

o

Water pump circulation anti freeze control activated, and water pump ON for 4 minutes

Backup heater turns OFF when

ANY

of the below conditions is fulfilled:

o

Water inlet/outlet temp. > 28°C

o

Water pump circulation anti freeze control deactivated/water pump OFF

However, if backup heater is abnormal (H70), then backup heater anti freeze control will not activate.

12.16 Solar Operation (Optional)

12.16.1 Solar Operation

1 External solar heat source signal can be connect to unit for proper control of heat source switching during

tank boiling time.

2  Control according to preset whether solar priority is set or not.
3  When tank connection is NOT set at SETTING mode, solar operation is disabled.
4  When Pump A (from solar pump station) is detected On through connection Y3 and Y4, then the Solar pump

3 Way Valve is requested ON (Refer to figure below).

12.16.2 Solar Operation Control

When solar priority is SET
1 Operation

condition:

a

3 way valve operates if all of the following conditions are fulfilled:

Power On. (regardless operation ON or OFF)

There is operation request from solar pump station.

Tank hot water temp is below solar on upper limit temp 72°C.

2 Stop

condition:

a

3 way valve stops operating when:

No power supply to unit

OR

There

is

NO

operation request from solar pump station

OR

Tank hot water temp is above solar off upper limit temp 80°C.

* heat pump OFF OR operate to room side when solar pump operate during solar priority set.
* booster heater OFF when solar pump operate during solar priority set.

When solar priority is NOT SET
1 Operation

condition:

a

3 way valve operates if all of the following conditions are fulfilled:

Power On. (regardless operation ON or OFF).

There is operation request from solar pump station.

Tank hot water temp is below solar on upper limit temp 72°C.

Heat pump thermo OFF in tank mode OR Heat pump operate to room side

(during operation ON and tank mode selected).

«
...
59
60
61
62
63
...
»

Содержание WH-MXF09D3E8






























































































































Отзывы:

Нет отзывов

Похожие инструкции для WH-MXF09D3E8

Бренд: Raypak Страницы: 36

Бренд: Macnaught Страницы: 12

Бренд: Kampmann Страницы: 16

Бренд: Kamco Страницы: 2

Бренд: machine technologies Страницы: 43

Бренд: IDEAL Страницы: 30

Бренд: Ulvac Страницы: 27

GSH-100ERA series

Бренд: Sinclair Страницы: 64

Бренд: Kohler Страницы: 13

Бренд: Milton Roy Страницы: 43

Бренд: nedis Страницы: 36

Бренд: VEAB Страницы: 4

Бренд: Oceanic Страницы: 33

REMINGTON REM-16-TTC-O

Бренд: Pinnacle Climate Technologies Страницы: 32

Бренд: True North Страницы: 20

Бренд: Pro-Elec Страницы: 4

Бренд: EQUATION Страницы: 48

Бренд: Sunbeam Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды